Okofen PELLETRONIC TOUCH Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 108

background image

Pellematic settings

74

Hyst Flue Gas Temp

The flue gas temperature must be above the boiler temperature plus Hyst Flue Gas
Temp for a successful ignition.

Min Flue Gas TempMax
Flue Gas Temp

Is the minimum and maximum limit of the flue gas temperature for the ignition.

27.3 Full power settings

Full power settings

is in the menu Pellematic

Full power settings has following menu items:

• Fuel Adjustment

• De+

• Air Flow Rate ++

• Flue Gas Fan ++

The additional menu items

Full power settings

are for the ÖkoFEN Service technician. They are present after

entering the code:

Fuel Adjustment

The run duration of the burner auger is calculated from the boiler controller. It
is independent from the rated power and the boiler set temperature and is set
automatically. The burner motor is then controlled accordingly. You can raise or
reduce the run time, calculated by the boiler controller, respective in 10 steps.

De+

Adjustment of the run time of the burner motor in the Full Power mode. Expressed
in tenths of a second.

Air Flow Rate ++

Adjusting the speed of the combustion air fan in the Full Power mode.

Flue Gas Fan ++

Adjusting the flue gas fan in the Full Power mode.

Operating manual Pelletronic Touch

E1389EN 2.0

«
...
72
73
74
75
76
...
»

Содержание PELLETRONIC TOUCH













































































































Отзывы:

Нет отзывов

Похожие инструкции для PELLETRONIC TOUCH

Бренд: Quickmill Страницы: 3

Бренд: Ickle Bubba Страницы: 23

Бренд: Baby Jogger Страницы: 16

Бренд: Salda Страницы: 16

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Madison AV Страницы: 2

Бренд: Radionics Страницы: 14

1E0671-1 MCR2.9

Бренд: Haberl Electronic Страницы: 9

Бренд: J+J Страницы: 2

Бренд: Vag Страницы: 15

Бренд: Securi-Prod Страницы: 3

Бренд: DS Produkte Страницы: 4

Бренд: GEM Страницы: 56

Бренд: Lunt Solar Systems Страницы: 4

Бренд: BG Systems Страницы: 24

Бренд: Powtran Страницы: 36

5400 Pilot Operated

Бренд: Valve Concepts Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды