background image

EN-16                                                        

Ranger™ Count 3000

 

Series

 

Auto Tare

 [

A.tArE

]

  

Set the automatic tare functionality.  

 

OFF 

= Automatic Tare is disabled 

 

ON 

= the first stable gross weight is tared 

 

ON-ACC  = stable gross loads within the accept limits are tared (in Check weighing mode) 

 

Beeper Opt [

bp.OPt

]

  

Set whether or not the beeper sounds when APW has been optimized. 

 

OFF 

= disabled 

 

ON 

= enabled 

 

Beeper Signal

 [

Bp.sIG

]

  

Set how the beeper responds in Check Weighing mode. 

 

OFF 

  = the beeper is disabled 

 

ACCEPT   = the beeper will sound when the weight is within the Accept range. 

 

UNDER    = the beeper will sound when the weight is below the Under setting. 

 

OVER    = the beeper will sound when the weight is above the Over setting. 

 

OVER- 

 

UNDER    = the beeper will sound when the weight is below the Under setting or above the 

 

 

     Over setting. 

 

Beeper Key

 [

BP.key

]

  

Set whether the beeper sounds when a button is pressed. 

 

OFF 

= disabled 

 

ON 

= enabled

 

Accumulation

 [

aCCUmM

]

  

Set the accumulation functionality.  

 

OFF 

= accumulation disabled 

 

AUTO  = automatic accumulation 

 

MAN 

= manual accumulation 

 
End Setup

 [

End

]

  

Advance to the next menu or return to the top of the current menu. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Ranger Count RC1P1502









































Отзывы: