100
Pompe à chaleur pour piscine à onduleur
FR
Étape 1: Retirez l'unité de commande de l'appareil. Faites attention au câble de
communication connecté à la carte de circuit imprimé et débranchez-le soigneu-
sement.
Étape 2: Utilisez un tournevis pour ouvrir le boîtier et retirez l'unité de commande.
Étape 3: Percez deux trous parallèles à hauteur des yeux : entraxe 60 mm.
Étape 4: Fixez le couvercle arrière de l'unité de commande au mur.
Étape 5: Alignez les couvercles avant et arrière et assurez-vous que le boîtier est
solidement fi xé au mur.
Étape 6: Branchez soigneusement le câble de communication.
Étape 1
Étape 3
Étape 5
Étape 2
Étape 4
Étape 6
Montage mural de l'unité
de commande
3.9
NOTE IMPORTANTE :
N'utilisez pas d'objets tranchants lorsque vous touchez le panneau avant et les
touches de l'unité de commande, car cela pourrait les endommager. Quand l'unité
de commande est fi xée au mur, ne tirez pas sur le câble de communication. Cela
pourrait desserrer le câblage et endommager le contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
