Oce WP28 Скачать руководство пользователя страница 107

Страница: 107 / 227

Configuration

1-91

Configuration

This section explains the details of printer settings. The following items

are covered.
• Page Protect Mode
• Linefeed (LF) Action
• Carriage-Return (CR) Action
• Wide A4 Pitch
• Print Density
• Total Printed Pages
• Toner Counter Resetting
• Message Language
• Automatic Form Feed Timeout
• Sleep Timer Setting
• Printer Resetting
• Resource Protection
• Alarm (Buzzer) Setting
• Auto Continue Setting
• Duplex Printing Error Detection Setting

Page Protect Mode

The Page Protect Menu does not normally appear, however,

Page Protect

will be forcibly set to On if a print overrun error occurs due to insufficient

printer memory. When this has happened, be sure to reset

Page Protect

Auto

(default) in order to maintain the optimum use of printer memory.

Press the

MENU

key.

Press the or key repeatedly until

Page set >

appears.

Press the

key.

Press the or key repeatedly until

>Page Protect

appears.

Page set

>Page Protect
On

Содержание WP28




































































































































































































































Результаты поиска

Содержание WP28

Отзывы:

Похожие инструкции для WP28

Бренды по названию

Популярные бренды

Oce WP28, Руководство по эксплуатации

Результаты поиска

Содержание WP28

Отзывы:

Похожие инструкции для WP28

Бренды по названию

Популярные бренды