Oce WP28 Скачать руководство пользователя страница 103

Страница: 103 / 227

Operating the Storage Device

1-87

Reading Fonts from a CompactFlash Card

If a font (CompactFlash) card is already inserted into the slot when the

printer is turned on, the fonts are automatically read into the printer.
To re-read fonts into the printer from a CompactFlash card, proceed as

follows.

Press the

MENU

key.

Press the or key repeatedly until

Memory Card >

appears.

Press the

key.

Press the or key repeatedly until

>Read Fonts

appears.

Press the

ENTER

key. A question mark (

) appears.

Press the

ENTER

key.

Processing

appears and the reading of fonts

from the CompactFlash card starts.

When the reading of fonts ends, the message display returns to

>Read fonts

Press the

MENU

key. The message display returns to

Ready

Memory Card

>Read Fonts

>Read Fonts ?

Содержание WP28




































































































































































































































Результаты поиска

Содержание WP28

Отзывы:

Похожие инструкции для WP28

Бренды по названию

Популярные бренды

Oce WP28, Руководство по эксплуатации

Результаты поиска

Содержание WP28

Отзывы:

Похожие инструкции для WP28

Бренды по названию

Популярные бренды