NXP Semiconductors MSC8113 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 1202

background image

Power-On Reset (PORESET)

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

5-3

BM[0–2]

Boot Mode
Input lines sampled at the rising edge of PORESET,
which determine the MSC8113 boot mode.

Refer to Table 6-1, Boot Mode Selection, on page
6-1.

SWTE

Software Watchdog Timer Enable
Input line sampled at the rising edge of PORESET.
This bit defines whether the software watchdog
timer is enabled or disabled. For details on how this
signal functions, refer to the discussion of the
System Protection Control Register (SYPCR) in
Section 4.2, SIU Programming Model.

0

Watchdog timer disabled.

1

Watchdog timer enabled.

DSI64

DSI 64-Bit Data Bus
Input line sampled at the rising edge of PORESET.
This input combined with ETHSEL hard reset
configuration bit, define the pin multiplexing of the
low part of the MSC8113 DSI/system data bus with
the Ethernet. For details on how the DSI64 signal
functions, refer to Section 14.5.2, Status Registers,
on page 14-35). For details on how the ETHSEL bit
functions, refer to Section 5.6.1, Hard Reset
Configuration Word, on page 5-13.

For details on DSI/system bus/Ethernet pin
multiplexing configuration, please refer to Table 5-4
on page 5-3.

DSISYNC

DSI Synchronous Mode
Input line sampled at the rising edge of PORESET.
This bit defines whether the DSI
works in Synchronous or Asynchronous Mode. For
details, refer to Section 14.3.2, Synchronous
Versus Asynchronous Access Mode.

0

Asynchronous mode.

1

Synchronous mode.

CHIP_ID[0–3]

Chip ID
Input line sampled at the rising edge of PORESET.
These bits define the unique number for each
MSC8113 in a multi-MSC8113 system (up to 16).
The DSI compares these bits to the HCID[0–3] input
bus to identify access to the specific MSC8113. For
details on how these signals function, refer to
Section 14.2.3, Host Chip ID Signals (HCID[0–3])).

Any value between 0b0000–0b1111.

MODCK[1–2]

Clock Mode
Input line sampled at the rising edge of PORESET.
For details on how these signals function, refer to
Section 7.3, Clock Configuration.

Table 5-4. DSI/System Bus/Ethernet Signal Multiplexing Configurations

DSI64

(Po-Reset

Configuration Pin)

ETHSEL

(Hard Reset

Configuration Bit)

DSI bus width

System bus width

ETH is exposed on

the low part of the

DSI/System data bus

(HD[32–63]/D[32–63])

0

0

32 bit

64 bit

No

0

1

32 bit

32 bit

Yes

1

x

64 bit

32 bit

No

Table 5-3. PORESET External Configuration Signals (Continued)

Signal Description

Settings

«
...
135
136
137
138
139
...
»

Содержание MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8113

Professional Series

Бренд: PACOM Страницы: 15

Бренд: XDS Страницы: 99

Бренд: Ebyte Страницы: 8

Бренд: ICP DAS USA Страницы: 8

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Lancom Страницы: 70

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: S&P Страницы: 3

Бренд: ProSoft Страницы: 53

Бренд: Extron electronics Страницы: 19

Бренд: NEC Страницы: 47

H8S/2615 Series

Бренд: Renesas Страницы: 28

Бренд: ICP DAS USA Страницы: 8

Бренд: ZyXEL Communications Страницы: 263

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

Бренд: Forcepoint Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды