NXP Semiconductors MSC8113 Скачать руководство пользователя страница 470 | Manualshive

Страница: 470 / 1202

background image

MSC8113 Reference Manual, Rev. 0

14-10

Freescale Semiconductor

Direct Slave Interface (DSI)

14.2.3 Host Chip ID Signals (HCID[0–3])

The CHIPID field in the DSI Chip ID Register (DCIR) (see page 14-34) contains the value of the

CHIP_ID[0–3]

signals that is sampled during the

PORESET

sequence. For each host access to the

DSI, the

HCID[0–3]

signals are compared to the DCIR[CHIPID] value. This decoding enables the

host to use one chip select signal to access each of up to sixteen MSC8113 devices. You can write
a new value to the DCIR after the reset sequence ends.

HCID[3]

is multiplexed with

HA[8]

which

means that it is used as address bit and not a Chip ID bit, if DCR[ADREN] equals 0b0011 or
0b0100 (see page 14-34). In this case, you should ensure that

CHIPID[3]

is sampled low during the

PORESET

sequence.

14.2.4 DSI Endian Modes

The DSI supports hosts that use big-endian, little-endian, or munged little-endian byte ordering.
The LTLEND bit in the Hard Reset Configuration Word (HRCW) is set for host accesses in
Little-Endian mode. A host working in munged Little-Endian mode must also set the PPCLE bit
in the HRCW (see Section 5.6.1, Hard Reset Configuration Word, on page 5-13 and Section
3.1.4 in The Programming Environments for 32-Bit Processors that Implement the PowerPC
Architecture (MPCFPE32B/AD)).

MSC8113 internal memory is structured as big-endian, so the DSI reorganizes data structures
written by little-endian hosts. When bit LTLEND is set, the DSI translates all host accesses to the
big-endian structure before placing them in the internal memory space. The translation of a
little-endian host access to a big-endian structure occurs according to the type of the data
structure in the access; that is, according to whether the data structure is 8-bit, 16-bit, 32-bit, or
64-bit. The DCR[DSRFA] bit defines how the host declares the type of the data structure in the
access:

Using the

HDST[0–1]

signals (see Table 14-4)

Using the DCR[LEDS] field

Note:

The DSI refers to host accesses to MSC8113 registers as 32-bit data structure accesses,
overriding any value defined by the

HDST[0–1]

signals or by the DCR[LEDS] field.In

munged little-endian mode, when working with 32 bit data bus width, prefetch
mechanism is not supported. In this combination of modes bit DCR[RPE] should not
be set.

Table 14-4. HDST[0–1] Signal Decoding

HDST[0–1]

00

01

10

11

Data Structure

8 bit

16 bit

32 bit

64 bit

«
...
468
469
470
471
472
...
»

Содержание MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8113

Бренд: TC Electronic Страницы: 2

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: Pressalit Care Страницы: 31

Бренд: Lanner Страницы: 38

Бренд: MSNswitch Страницы: 2

COM Express conga-TC87

Бренд: Congatec Страницы: 114

Бренд: LST Страницы: 1

Бренд: Cypress Semiconductor Страницы: 18

Kontron CP3005 Series

Бренд: S&T Страницы: 115

Braswell Series

Бренд: Intel Страницы: 54

Бренд: NEC Страницы: 114

Бренд: Akasa Страницы: 2

EK-Quantum Vector FE RTX 3080

Бренд: ekwb Страницы: 20

Бренд: IEI Technology Страницы: 119

GigaVUE H Series

Бренд: Gigamon Страницы: 55

Database Appliance X6-2-HA

Бренд: Oracle Страницы: 473

Audio Plus 3200

Бренд: Zoltrix Страницы: 34

Бренд: Icop Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды