NXP Semiconductors MSC8113 Скачать руководство пользователя страница 346 | Manualshive

Страница: 346 / 1202

background image

MSC8113 Reference Manual, Rev. 0

12-38

Freescale Semiconductor

Memory Controller

When ORx[TRLX] and ORx[CSNT] are set in a write-memory access, the strobe lines,

PWE[0–7]

are deasserted one clock earlier than in the normal case. If ORx[ACS]

≠

00,

CS

is also deasserted

one clock earlier, as shown in Figure 12-38 and Figure 12-39. When a bank is selected to
operate with external transfer acknowledge (ORx[SETA] = 1 and ORx[TRLX] = 1), the memory
controller does not support external devices that provide

PSDVAL

to complete the transfer with

zero wait states. The minimum access duration in this case is three clock cycles.

12.3.1.4 Output Enable (POE) Timing

The timing of the

POE

is affected only by TRLX. It always asserts and deasserts on the rising

edge of the external bus clock.

POE

always asserts on the rising clock edge after

CS

is asserted,

and therefore its assertion can be delayed (along with the assertion of

CS

) by programming

ORx[TRLX] = 1.

POE

deasserts on the rising clock edge coinciding with or immediately after

CS

deassertion.

12.3.1.5 Programmable Wait State Configuration

The GPCM supports internal

PSDVAL

generation. It allows fast accesses to external memory

through an internal 60x-compatible bus master or a maximum 17-clock access by programming
ORx[SCY]. The internal

PSDVAL

generation mode is enabled if ORx[SETA] = 0. If

PGTA

is

asserted externally at least two clock cycles before the wait state counter expires, the current
memory cycle is terminated. When ORx[TRLX] = 1, the number of wait states inserted by the
memory controller is defined by 2

×

SCY or a maximum of 30 wait states.

Figure 12-37. GPCM Relaxed-Timing Write (ACS = 1x, SCY = 0, CSNT = 0,TRLX = 1)

Clock

Address

PSDVAL

CSx

BCTL0

PWE

POE

Data

ACS = 10

ACS = 11

«
...
344
345
346
347
348
...
»

Содержание MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8113

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Tripp Lite Страницы: 20

Бренд: SeaLevel Страницы: 17

Бренд: Maxim Страницы: 14

Бренд: Dahua Страницы: 113

Бренд: Acromag Страницы: 35

Бренд: Navitar Страницы: 1

Бренд: ICP Страницы: 142

Бренд: Rimage Страницы: 30

Бренд: Xaoc Devices Страницы: 4

STEVAL-IHT003V1

Бренд: ST Страницы: 20

Бренд: X-Micro Страницы: 24

UEZGUI-4357-70WVN

Бренд: FDI Страницы: 30

Бренд: Panasonic Страницы: 78

Бренд: Extron electronics Страницы: 139

Бренд: Crestron Страницы: 8

Serial ATA PCI RAID

Бренд: SIIG Страницы: 36

Бренд: AJA Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды