NXP Semiconductors MSC8113 Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 1202

background image

Basic Architecture

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

12-11

12.1.9 ECC/Parity Byte-Select (PPBS)

Systems that use ECC or RMW parity require an additional memory device that requires
byte-select like a normal data device. ANDing

PBS[0–7]

through external logic to achieve the

logical function of this byte-select can affect the memory access timing because it adds a delay to
the byte-select path. The optional memory controller parity-byte-select signal is an internal AND
of the eight byte-selects, allowing glueless and faster connection to ECC/RMW-parity devices.
This option is enabled by setting SIUMCR[PBSE], as described in Section 4.2, SIU
Programming Model.

12.1.10 Data Pipelining

Multiple-MSC8113 systems that use data checking, such as parity, face a timing problem when
synchronous memories, such as SDRAM, are used. Because these devices can output data every
cycle and because the data checking requires additional data set-up time, the timing constraints
are extremely hard to meet. In such systems, you can eliminate the additional data set-up time
requirement by setting the data pipelining bit, BRx[DR]. This creates data pipelining of one stage
within the memory controller in which the data check calculations are done.

In systems that involve both PowerQUICC II-type masters and a 60x-compatible master, this
feature can still be used on the system bus with the following restrictions:

The arbiter and the memory controller are in the same MSC8113.

The register field BCR[NPQM] is set correctly.

See Section 12.6, External Master Support (60x-Compatible Mode), on page 12-83, and the
discussion of the Bus Configuration Register (BCR) in Section 4.2, SIU Programming Model.

Figure 12-8. Partial Data Valid for 32-Bit Port Size Memory, 64-bit Transfer

Clock

External

PSDVAL

Internal

TA

Data Bus

Data Bus

(32 MSB)

(32 MSB)

Upper 4 bytes

Lower 4 bytes

Internal

Data Bus

(32 LSB)

Upper 4 bytes

Lower 4 bytes

«
...
317
318
319
320
321
...
»

Содержание MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MSC8113

Бренд: Paradyne Страницы: 12

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: Amperes Страницы: 8

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Cisco MERAKI Страницы: 4

Бренд: Xantech Страницы: 16

Бренд: Icy Box Страницы: 2

Бренд: ASROCK Страницы: 173

Бренд: Rosewill Страницы: 2

Бренд: swiftech Страницы: 2

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

Бренд: IBM Страницы: 242

Бренд: ZyXEL Communications Страницы: 263

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

Бренд: Citizen Страницы: 50

Бренд: GE Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды