manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MC9S08PA4 Скачать руководство пользователя страница 308

15.4.1 Clock select and divide control

One of four clock sources can be selected as the clock source for the ADC module. This
clock source is then divided by a configurable value to generate the input clock to the
converter (ADCK). The clock is selected from one of the following sources by means of
the ADC_SC3[ADICLK] bits.

• The bus clock, which is equal to the frequency at which software is executed. This is

the default selection following reset.

• The bus clock divided by 2: For higher bus clock rates, this allows a maximum

divide by 16 of the bus clock.

• ALTCLK, that is, alternate clock which is OSCOUT

• The asynchronous clock (ADACK): This clock is generated from a clock source

within the ADC module. When selected as the clock source, this clock remains active
while the MCU is in Wait or Stop3 mode and allows conversions in these modes for
lower noise operation.

Whichever clock is selected, its frequency must fall within the specified frequency range
for ADCK. If the available clocks are too slow, the ADC does not perform according to
specifications. If the available clocks are too fast, the clock must be divided to the
appropriate frequency. This divider is specified by the ADC_SC3[ADIV] bits and can be
divide-by 1, 2, 4, or 8.

15.4.2 Input select and pin control

The Pin Control registers ( ADC_APCTL2 and ADC_APCTL1) disables the I/O port
control of the pins used as analog inputs. When a pin control register bit is set, the
following conditions are forced for the associated MCU pin:

• The output buffer is forced to its high impedance state.

• The input buffer is disabled. A read of the I/O port returns a zero for any pin with its

input buffer disabled.

• The pullup is disabled.

Functional description

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

308

NXP Semiconductors

Содержание MC9S08PA4


















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды