manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MC9S08PA4 Скачать руководство пользователя страница 170

ICS_C4 field descriptions (continued)

Field

Description

0

No request on loss of lock.

1

Generate an interrupt request on loss of lock.

6

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

5

CME

Clock Monitor Enable

Determines if a reset request is made following a loss of external clock indication. The CME bit should be
set to a logic 1 only when the ICS is in an operational mode that uses the external clock (FEE or FBE).

0

Clock monitor is disabled.

1

Generate a reset request on loss of external clock.

4–1

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

0

SCFTRIM

Slow Internal Reference Clock Fine Trim

The SCFTRIM bit controls the smallest adjustment of the internal reference clock frequency. Setting
SCFTRIM will increase the period and clearing SCFTRIM will decrease the period by the smallest amount
possible.

NOTE: SCFTRIM is loaded during reset from a factory programmed location when not in any BDM mode.

8.6.5 ICS Status Register (ICS_S)

Address: 3038h base + 4h offset = 303Ch

Bit

7

6

5

4

3

2

1

0

Read

LOLS

LOCK

0

IREFST

CLKST

0

Write

Reset

0

0

0

1

0

0

0

0

ICS_S field descriptions

Field

Description

7

LOLS

Loss of Lock Status

This bit is a sticky indication of lock status for the FLL. LOLS is set when lock detection is enabled and
after acquiring lock, the FLL output frequency has fallen outside the lock exit frequency tolerance, D

unl

.

LOLIE determines whether an interrupt request is made when set. LOLS is cleared by reset or by writing a
logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect.

0

FLL has not lost lock since LOLS was last cleared.

1

FLL has lost lock since LOLS was last cleared.

6

LOCK

Lock Status

Indicates whether the FLL has acquired lock. Lock detection is disabled when FLL is disabled. If the lock
status bit is set then changing the value of any of the following bits IREFS, RDIV[2:0], or, if in FEI or FBI
modes, TRIM[7:0] will cause the lock status bit to clear and stay cleared until the FLL has reacquired lock.

Table continues on the next page...

ICS control registers

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

170

NXP Semiconductors

Содержание MC9S08PA4


















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды