manualshive.com logo in svg

NXP Semiconductors freescale semiconductor MC13211, Справочное руководство

NXP Semiconductors freescale semiconductor MC13211 - На этом сайте вы можете бесплатно скачать руководство по эксплуатации для продукта MC13211. Скачайте его с manualshive.com и ознакомьтесь с полезной информацией о продукте. В руководстве вы найдете все необходимые сведения для правильного использования устройства.

Поделиться
Скачать
background image

MCU Serial Communications Interface (SCI)

MC1321x Reference Manual, Rev. 1.6 

Freescale Semiconductor

18-3

The transmitter is enabled by setting the TE bit in SCIxC2. This queues a preamble character that is one 
full character frame of logic high. The transmitter then remains idle (TxD1 pin remains high) until data is 
available in the transmit data buffer. Programs store data into the transmit data buffer by writing to the SCI 
data register (SCIxD).

The central element of the SCI transmitter is the transmit shift register that is either 10 or 11 bits long 
depending on the setting in the M control bit. For the remainder of this section, we will assume M = 0, 
selecting the normal 8-bit data Mode. In 8-bit data Mode, the shift register holds a start bit, eight data bits, 
and a stop bit. When the transmit shift register is available for a new SCI character, the value waiting in 
the transmit data register is transferred to the shift register (synchronized with the baud rate clock) and the 
transmit data register empty (TDRE) status flag is set to indicate another character may be written to the 
transmit data buffer at SCIxD.

If no new character is waiting in the transmit data buffer after a stop bit is shifted out the TxD1 pin, the 
transmitter sets the transmit complete flag and enters an idle mode, with TxD1 high, waiting for more 
characters to transmit.

Writing 0 to TE does not immediately release the pin to be a general-purpose I/O pin. Any transmit activity 
that is in progress must first be completed. This includes data characters in progress, queued idle 
characters, and queued break characters.

18.4.2

Send Break and Queued Idle

The SBK control bit in SCIxC2 is used to send break characters that were originally used to gain the 
attention of old teletype receivers. Break characters are a full character time of logic 0 (including a 0 where 
the stop bit would be normally). Normally, a program would wait for TDRE to become set to indicate the 
last character of a message has moved to the transmit shifter, then write 1 and then write 0 to the SBK bit. 
This action queues a break character to be sent as soon as the shifter is available. If SBK is still 1 when the 
queued break moves into the shifter (synchronized to the baud rate clock), an additional break character is 
queued. If the receiving device is another Freescale Semiconductor SCI, the break characters will be 
received as 0s in all eight (or nine) data bits and a framing error (FE = 1).

When idle-line wakeup is used, a full character time of idle (logic 1) is needed between messages to wake 
up any sleeping receivers. Normally, a program would wait for TDRE to become set to indicate the last 
character of a message has moved to the transmit shifter, then write 0 and then write 1 to the TE bit. This 
action queues an idle character to be sent as soon as the shifter is available. As long as the character in the 
shifter does not finish while TE = 0, the SCI transmitter never actually releases control of the TxD1 pin. 
If there is a possibility of the shifter finishing while TE = 0, set the general-purpose I/O controls so the pin 
that is shared with TxD1 is an output driving a logic 1. This ensures that the TxD1 line will look like a 
normal idle line even if the SCI loses control of the port pin between writing 0 and then 1 to TE.

18.5

Receiver Functional Description

In this section, the receiver block diagram (

Figure 18-3

) is used as a guide for the overall receiver 

functional description. Next, the data sampling technique used to reconstruct receiver data is described in 
more detail. Finally, two variations of the receiver wakeup function are explained.

Содержание freescale semiconductor MC13211





















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для freescale semiconductor MC13211

Absolute Process Instruments DuoPak APD 2015 Instructions preview
DuoPak APD 2015
Бренд: Absolute Process Instruments Страницы: 2
Eaton COOPER POWER SERIES Installation, Operation, And Maintenance Instructions And Parts Replacement Information preview
COOPER POWER SERIES
Бренд: Eaton Страницы: 24
Eaton COOPER POWER SERIES Installation And Maintenance Instructions Manual preview
COOPER POWER SERIES
Бренд: Eaton Страницы: 32
Omega TX12 Instruction Sheet preview
TX12
Бренд: Omega Страницы: 2
Renke RS-FX Series Instruction Manual preview
RS-FX Series
Бренд: Renke Страницы: 10
Nakamichi DELTA 10B User Manual preview
DELTA 10B
Бренд: Nakamichi Страницы: 8
SportIQ Smart Tag ST008 User Manual preview
Smart Tag ST008
Бренд: SportIQ Страницы: 3
a-them AVM 60 Operating Manual preview
AVM 60
Бренд: a-them Страницы: 66
Marantz SR7013 Product Information preview
SR7013
Бренд: Marantz Страницы: 2
Icom iC-F3033S Instruction Manual preview
iC-F3033S
Бренд: Icom Страницы: 32
M-system VOS2T Instruction Manual preview
VOS2T
Бренд: M-system Страницы: 4
SYD TD-780 Technical Manual preview
TD-780
Бренд: SYD Страницы: 9
CHUNDE TECHNOLOGY CH-CO Manual For Installation preview
CH-CO
Бренд: CHUNDE TECHNOLOGY Страницы: 2
Cinelex DESK-TX8 Operation Manual preview
DESK-TX8
Бренд: Cinelex Страницы: 6
Laser SPK-WFADAPTOR Quick User Manual preview
SPK-WFADAPTOR
Бренд: Laser Страницы: 6
Dakota Micro AgCam DMAC-RH User Manual preview
AgCam DMAC-RH
Бренд: Dakota Micro Страницы: 2
NHK Bigear Instruction Manual preview
Bigear
Бренд: NHK Страницы: 14
Marmitek Boomboom 90 User Manual preview
Boomboom 90
Бренд: Marmitek Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды