Novanta IMS Liberty MDrive CANopen Скачать руководство пользователя страница 70

Страница: 70 / 86

IMS-MN-LMDA42C_A.pdf

Appendix A:

Diagnostics and Troubleshooting

Operation State and Error Indication

Temperature Monitoring

Sensors in the drive measure the temperature of the power stage. If the permissible maximum

temperature is exceeded, the power stage is de-energized. Indication can be read by reading

object 2019h Output h-bridge temperature options, subindex 01h.

Stall Detection (hMT Disabled)

Detecting a stall condition may be accomplished by monitoring the encoder via the

communications interface on models equipped with an encoder.

When hMT is enabled, a stopped shaft or locked rotor will be indicated by assertion of a locked

rotor error.

Locked Rotor (hMT Enabled)

A locked rotor indication identifies the condition where the rotor/stator relationship exceeded

lead/lag limits

and/or locked rotor timeout

(LT)

as specified during parameterization. When

this condition occurs the power stage will disable and a locked rotor error is asserted.

A locked rotor error condition can only occur when hMT is enabled. This status may be read

using the hMT status bits or error codes.

LED Indicators

The LMD has two LEDs for status indication.

• LED 1: Status of the power supply.

• LED 2: The CANopen status LED shows the states as specified in the

CiA DR-303-3 Indicator specification.

Color

State

Status

Power Indication (LED 1)

Off

None

No Power

Green

Solid

+VDC supply in range

Flashing

+VDC off, drive on AUX power

Red

Solid

+VDC supply out of range

Flashing

+VDC off, AUX power out of range

CANopen Status (LED 2)

Green

Solid

The Device is in the OPERATIONAL state

Single Flash

The Device is in STOPPED state

Flashing

The Device is in the PREOPERATIONAL state

Red

Solid

The CAN controller is bus off

Single Flash

At least one of the error counters of the CAN controller has reached or

exceeded the error level (too many error frames).

Double Flash

A guard event (NMT-Slave or NMT-master) or a heartbeat event (Heartbeat

consumer) has occurred.

Triple Flash

The SYNC message has not been received within the configured

communication cycle period time out (see Object Dictionary Entry 0x1006).

Содержание IMS Liberty MDrive CANopen























































































Результаты поиска

Содержание IMS Liberty MDrive CANopen

Отзывы:

Похожие инструкции для IMS Liberty MDrive CANopen

Бренды по названию

Популярные бренды

Novanta IMS Liberty MDrive CANopen, Руководство по оборудованию

Результаты поиска

Содержание IMS Liberty MDrive CANopen

Отзывы:

Похожие инструкции для IMS Liberty MDrive CANopen

Бренды по названию

Популярные бренды