background image

 

 

Preface 

For correct installation and operation, please read all instructions carefully. Before reading the instructions, 

please be aware of the following items: 

 

WARNING 

DANGER: Failure to comply may result in severe personal injury, property damage and/or 
death. 

CAUTION 

CAUTION: Failure to comply may result in personal injury and/or property damage. 

 

NOTICE is used to address practices not related to personal injury. 

 

WARNING

 

(1) Instructions for installation and use of this product are provided by the manufacturer. 

(2) Installation must be performed in accordance with the requirements of NEC and CEC by authorized personnel only. 

(3) For the safe operation of this unit, please read and follow the instructions carefully. 

(4) During operation, total capacity of indoor units should not exceed the total capacity of outdoor units, otherwise, poor 
cooling or heating performance may result. 
(5) Direct operators or maintainers should keep this manual for future reference. 

(6) If this unit fails to operate normally, please contact a qualified contractor as soon as possible and provide the 
following information: 

1) Content on the nameplate (model number, cooling capacity, serial number and manufacture date. 
2) Malfunction details (before and after the malfunction occurred). 

(7) Each unit has been strictly tested and proved before shiment. In order to prevent units from being damaged or 
malfunctioning because of improper service, please do not disassemble the unit by yourself. If you need to 
maintenance or service, please contact a qualified contractor. 
(8)In standby mode, the unit will consume a little power for normal communication, preheating refrigerant, etc. When 

the unit won’t be used for a long

 period of time, turn off the power of the complete unit.    Power will need to be turned 

back on 24 hours before the next time the air conditioner is used for warmup.. 
(9) Illustrations in this manual are for your reference only. Manuals are subject to change by manufacturer without prior 
notice. 

(10) Instructions are also be available online. 

User Notice 

    This appliance is not intended for use by persions (including children) with reduced physical, sensory or 

mental capabilities or lack of experience and knowledge. 

  DISPOSAL: Do not dispose this product as unsorted household waste. Please dispose or recyle 

responsibly.  

 

 

R410A(R32/125:50/50):2087.5 
 

 
 
 

 

 

Содержание BDFC-11.2-AK






















Отзывы: