manualshive.com logo in svg

Nordson Encore LT, Руководство по эксплуатации продукта

Поделиться
Скачать
Nordson Encore LT Скачать руководство пользователя страница 59

Repair

6-3

Part 1604857-04

E

 2014 Nordson Corporation

4. Press on the end of the power supply to ensure that the power supply

contact tip is firmly seated against the brass contact inside the gun body.

5. Route the power supply harness connector through the top hole in the

bulkhead.

Powder Path Replacement 

NOTE:  

Skip these steps if not replacing the powder path. Go to page 6-4

to reassemble the spray gun.
1. See Figure 6-4. Remove the elbow (18) from the inlet tube (25).
2. Remove the two M3 x 20 screws (12) from the handle base (27). Pull

the base away from the handle, swing the bottom of the ground pad (15)

up and away from the handle, then remove it. Leave the ground wire

connected to the ground pad.

3. Push the inlet tube (25) up and out of the base, then move the base out

of the way and pull the inlet tube out of the handle.

4. Push the outlet tube (4) out of the front of the gun body (13).
5. Blow off the inlet tube, outlet tube, and elbow, and replace them if the

interiors are worn or coated with impact-fused powder. If re-using the

tubes, make sure the O-rings are undamaged.

15

15

14

14

25

13

4

12

27

24

18

Figure 6-4

Powder Path Replacement

4. Outlet tube

12. M3 x 20 screws
13. Gun body

14. Air wash tubing

15. Ground pad

18. Elbow

24. Handle
25. Inlet tube
27. Handle base

Содержание Encore LT





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды