Nordson Encore LT Скачать руководство пользователя

Страница: 29 / 92

System Setup

3-13

Part 1604857-04

2014 Nordson Corporation

Bundling Tubing and Cable

Use the sections of black spiral-cut tubing supplied with the system to

bundle together the spray gun cable, air tubing, and powder hose. Coil the

bundled tubing and cable and hang the coil on the hook at the back of the

cart tower.

System Air Connections

System Air Supply

Compressed air should be supplied from an air drop equipped with a

self-relieving shutoff valve. The air must be clean and dry. A refrigerant or

desiccant-type air drier and air filters are recommended.

All systems are shipped with a 0.3-micron air filter. It is important that the

filter be used to prevent contamination of the system pneumatic

components and the powder supply.

Supply air pressure should be 4.0

−

7.6 bar (58

−

110 psi).

To provide air to your system, an input air kit with connectors, couplings,

and 10-mm air tubing (15-ft for dolly systems, 25-ft for wall/rail mount

systems) is available.

Refer to the

Parts

section for filter kits, replacement elements, and input air

kit part numbers and ordering information.

Mobile Systems

Connect 10-mm air tubing from your compressed air supply to the air input

fitting on the rear panel of the dolly.

Wall/Rail Mount Systems

See Figure 3-14.

1. Use the mounting bracket (4) as a template to mark and drill mounting

holes in the selected mounting surface. Make sure there is sufficient

clearance to connect air tubing and change the filter element.

2. Install the two male connectors (2) included in the kit in the filter input

and output ports.

3. Install the mounting bracket on the filter, using the included M5 screws

(3), on the side of the filter opposite the release latch (6).

4. Mount the filter with customer-supplied fasteners (7).
5. Note the orientation of the flow indicator (5) on the top of the filter. Cut

10-mm blue air tubing to the required lengths to connect the air supply

to the filter and the filter to the controller, then connect the tubing.

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды