Nordson Encore LT Скачать руководство пользователя

Страница: 47 / 92

Operation

4-13

Part 1604857-04

2014 Nordson Corporation

Maintenance

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

WARNING:

Before performing the following tasks, turn off the controller

and disconnect system power. Relieve system air pressure and disconnect

the system from its input air supply. Failure to observe this warning may

result in personal injury.

Recommended Cleaning Procedure for Powder Contact Parts

Nordson Corporation recommends using an ultrasonic cleaning machine

and Oakite

BetaSolv emulsion cleaner to clean spray gun nozzles and

powder path parts.

NOTE:

Do not immerse the electrode assembly in solvent. It cannot be

disassembled; cleaning solution and rinse water will remain inside the

assembly.
1. Fill an ultrasonic cleaner with BetaSolv or an equivalent emulsion

cleaning solution at room temperature. Do not heat the cleaning

solution.

2. Remove the parts to be cleaned from the gun. Remove the O-rings.

Blow off the parts with low-pressure compressed air.

NOTE:

Do not allow the O-rings to come in contact with the cleaning

solution.
3. Place the parts in the ultrasonic cleaner and run the cleaner until all

parts are clean and free of impact fusion.

4. Rinse all parts in clean water and dry before re-assembling the spray

gun. Inspect the O-rings and replace any that are damaged.

NOTE:

Do not use sharp or hard tools that will scratch or gouge the smooth

surfaces of powder contact parts. Scratches will cause impact fusion.

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды