Nordson Encore LT Скачать руководство пользователя

Страница: 26 / 92

System Setup

3-10

Part 1604857-04

2014 Nordson Corporation

Adapter Kit or Coupling Installation

−

Wall/Rail Mount Systems

Rail- and wall-mount systems are shipped with a pump adapter kit and a

coupling that allows the Encore pump to be used on HR and NHR hopper

pickup tubes that were designed for other types of pumps. The adapter kit

provides a permanent mounting and its use is recommended.

Coupling Installation

The coupling allows you to use the existing pump adapter.

1. Install the pump coupling on the existing pump adapter with a slight

twisting motion.

2. Install the Encore pump into the coupling with a slight twisting motion.

Adapter Installation

The adapter kit replaces existing pump adapters with external O-rings on all

threaded 0.360 in. ID pickup tubes.

1. Pull the pump adapter and pickup tube out of the pump mount on the

hopper lid.

2. Unscrew the pickup tube from the existing adapter.
3. Screw the pickup tube into the Encore pump adapter shipped with the

system.

4. Install the pump adapter and pickup tube into the pump mount.
5. Install the Encore pump into the pump adapter with a slight twisting

motion.

Hopper

Pickup Tube

Assembly

1. Remove

Existing Adapter

2. Replace With

Encore Adapter

Pump

Coupling

Coupling Installation

Adapter Installation

Pump

Adapter

Figure 3-10 Pump Mounting

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды