Nordson Encore LT страница 28 Скачать руководство пользователя

Страница: 28 / 92

System Setup

3-12

Part 1604857-04

2014 Nordson Corporation

Air Tubing and Powder Hose

1. See Figure 3-12. Connect the 6-mm black air tubing to the

quick-disconnect fitting in the gun handle.

2. Connect the 4-mm clear electrode air wash tubing to the barbed fitting in

the gun handle.

4-mm Clear Electrode
Air Wash Tubing

6-mm Black
Purge Air Tubing

Hose Adapter

Powder Hose

Gun Cable

Figure 3-12 Gun Connections

3. Connect the powder hose to the hose adapter, then plug the hose

adapter into the handle.

NOTE:

6 meters (20 ft) of 11 mm ID powder hose is shipped with the

system. If you must use a longer hose, switch to 1/2 inch ID powder hose.

Refer to

Parts

for hose part numbers.

4. Route the air tubing to the rear panel of the gun controller.
5. See Figure 3-4. Connect the 6-mm black tubing to the purge air

quick-disconnect fitting (8).

6. See Figure 3-13. Connect the 4-mm clear tubing and the flow control

valve supplied with the system to the air wash connector on the rear

panel as shown. The flow control valve can be located anywhere

desired. Use a tubing cutter to make sure the tube ends are square.

To Gun

Air Wash Connector

4-mm Tubing

Flow Control Valve

Figure 3-13 Flow Control Valve and Air Wash Tubing Connection

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды