background image

4.2.1 Cleaning Rubber Roller 

 

 

  This printer has several sets of rubber rollers to ensure high reliability of card 

 

  transportation. However, if the rollers are stained because of use of stained cards or 

 

  cards coated with special materials, transport error may occur due to reduced 

 

  transportation power. Though periodic cleaning of rollers may be performed by users

 

  with a certain level of experience, the following intensive cleaning should be done if 

 

  such transportation error occurs.

 

 

  

?

 Transport Rollers in Flip Turn Module

 

     

?

  Open Top Cover and rotate Turn Module so that the rollers 

 

         come to the position where the cleaning can be done easily.

 

         

?

 This operation is done with the green knob in the flip turn module.

 

 

     

?

  Press a soft cloth with alcohol to the rollers and rotate them.

 

         

?

 This operation is done by rotating Green handle located at inside of 

 

            side plate. 

 

 

  

?

 Transport Rollers 

 

     

?

  Open the left cover and insert a soft cloth with alcohol and press against rollers  

and rotate them. 

 

         

?

 This operation is done with Cleaning Knob located on the Front 

 

            Access Panel.

 

 

 

 
 

4.2.2 Applying grease to Pulley Shafts etc.

 

  Plastic rollers used in this Printer is made of self-lubricative plastics. 

 

Содержание PR5350


































































































Отзывы: