Nilfisk-Advance SC401 17 B Скачать руководство пользователя

Страница: 131 / 173

131

Service Manual – SC401, SCRUBTEC 344

30 - Solution System

Detergent Tank and Detergent System Cleaning

1 Drive the machine to the appointed disposal area

2 If equipped remove the ignition key, then disconnect the red battery connector

3 Lift the recovery tank cover and check that the recovery tank is empty; if not, empty it using the drain

hose

4 Close the recovery tank cover, then lift the recovery tank

5 Unscrew the cap (A) from the detergent bottle (B)

6 Remove the detergent bottle

7 Rinse and wash out the detergent bottle with clean water in the appointed disposal area

Note:

For a thorough washing of the Detergent System, the cleaning procedure can also be

performed with the detergent bottle full of water. Turn on the system with the flow set to

the maximum. It is advisable to perform this type of cleaning when the Detergent System is

dirt/encrusted up, because the machine has not been used/cleaned for a long time.

Replace the detergent bottle (B), then refit the plug (A).

Figure 8:

Содержание SC401 17 B














































































































































































Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды

Nilfisk-Advance SC401 17 B, Руководство по обслуживанию

Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды