Nilfisk-Advance SC401 17 B Скачать руководство пользователя страница 87

Страница: 87 / 173

Service Manual – SC401, SCRUBTEC 344

20 - Wheel System, Traction

Functional Description

The machine wheel system with drive system consists of front wheels with gearmotor (M3) and a pair of

pivoting rear wheels

The Gear motor unit (M3) with electric motor, reduction unit, differential and drive wheels is the main

machine support and fastening element of the brush deck lifting and lowering mechanism

Using the Operator presence sensor (S1, S2), the operator can start the machine The Speed adjuster (RV1)

adjusts the transfer speed To reverse the machine, press the Reverse Gear Switch (SW1)

When turning on the machine using the Ignition key (K1), the Drive wheels controller (EB3) checks that the

Operator presence sensors (S1, S2) are not active (through a signal emitted by the Main machine controller

(EB1); otherwise, it triggers an alarm (3 LED blinks) that is displayed on the Drive wheels controller, and

inhibits the drive system (see “

Drive wheels controller (EB3) alarms

” paragraph)

Note:

In most of the real usage cases, if there is not any failure, this safety feature

is not visible to the user because of the Drive wheels controller (EB3) is

turned on as soon as the user turns on the Ignition Key (K1), but the Operator

presence sensor signals are given to the Drive wheels controller (EB3) only

after the Main machine controller (EB1) is turned on pushing the Main button.

So, if the user turn on the machine pushing the Main button with

one hand on the Operator presence sensor (with the Ignition Key (K1)

already closed), the machine will start moving without any inhibit.

The alarm triggers only in case of real system failure or immediately after turning the

Ignition key (K1).

To reset and stop the Drive wheels controller (EB3) alarm, turn off and on again the machine without

placing your hands on the Operator presence sensors (S1, S2)

When the Operator presence sensors (S1, S2) are activated, the Main machine controller (EB1) turns on a

“drive enable” signal to the Drive wheels controller (EB3)

The Drive wheels controller (EB3) supplies power to the Gear motor unit (M3), with a voltage proportional

to the Speed adjuster (RV1) position The acceleration ramps and top speed can be set with the relevant

parameters (see “

Drive wheels controller (EB3) parameters

” paragraph)

Содержание SC401 17 B














































































































































































Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды

Nilfisk-Advance SC401 17 B, Руководство по обслуживанию

Результаты поиска

Содержание SC401 17 B

Отзывы:

Похожие инструкции для SC401 17 B

Бренды по названию

Популярные бренды