Nilfisk-Advance 56108110 SC8000 48 LPG, Руководство по обслуживанию

Страница: 118 / 225

raulic S ste 8 Service Manual – SC8000
rou les ootin
eneral rou les ootin
Problem Cause Correction
Fault code 34
displayed on the
LCD Hydraulic temperature fault that sets when
hydraulic oil temperature exceeds 220 F for
15 seconds.
&OHDQWKHFRROLQJ¿QVRQWKH
hydraulic oil cooler to ensure
DGHTXDWHDLUÀRZWKURXJKWKHFRROHU
Fault code 39
displayed on the
LCD
+\GUDXOLF¿OWHUIDXOWVHWVWRZDUQRSHUDWRU
WKDWRLO¿OWHULVSOXJJHGDQGQHHGVWREH
replaced.
Note: Only activates when oil temperature
is above 100 degrees F (this prevents false
signal upon cold engine start up).
5HSODFHK\GUDXOLFRLO¿OWHU
eneral n or ation e ar in C ec in raulic ressures
Accurate measurements are the key to troubleshooting a hydraulic system. Once you obtain accurate
PHDVXUHPHQWV\RXFDQFRPSDUHWKHPWRWKHVSHFLÀFDWLRQVWRDQDO\]HDSUREOHP
<RXFDQXVHGLJLWDOWDFKRPHWHUVÁRZJDXJHVRUSUHVVXUHJDXJHVWRWURXEOHVKRRWWKHK\GUDXOLFV\VWHP
The pressure gauge should have a range of 0 to 3000 psi (see the
S ecial ools
section) and have a Parker
'LDJQRVWLFVFRQQHFWRUQXPEHU3'7KHPRVWFRQYHQLHQWZD\WRFKHFNIRURLOÁRZLVWRFKHFNWKH530RI
the motor that is performing poorly. Refer to the
6SHFL¿FDWLRQV
WDEOHVWRGHWHUPLQHWKHPRWRU530,IWKH
PRWRUVSHHGLVFRUUHFWWKHSXPSLVSURGXFLQJWKHFRUUHFWDPRXQWRIRLOÁRZ+RZHYHUWKLVGRHVQRWPHDQ
that if a motor is running too slow the problem is in the pump.
7KHIROORZLQJLQIRUPDWLRQVKRXOGEHXVHGWRFKHFNIRUFRUUHFWPRWRU530V\VWHPSUHVVXUHDQGUHOLHIYDOYH
VHWWLQJV7KHUHDGLQJVDUHQRPLQDOÀJXUHVDQGWKHUHZLOOEHYDULDWLRQVGXHWRPDQXIDFWXULQJWROHUDQFHV
and system oil temperature. If any reading varies greater than 20 percent, there will be a noticeable loss of
performance and the problem should be corrected.
est ort o inal ressure ea in s
Note: 6HHWKHÀJXUHRQWKHIROORZLQJSDJHDQGWKH
6SHFL¿FDWLRQV
tables.
100 psi = 6.9 bar.
1. Insert the pressure gauge into the test port.
Note: The Lower Test Port (TP 4) on the Scrub Lift Cylinder is easier to access if you lower the
scrub deck.
2. 5XQWKHHQJLQHLQKLJKWKURWWOHSRVLWLRQ530DQGDOORZWKHK\GUDXOLFRLOWRZDUPXS
‡ The bypass pressure is the pressure reading with no motor or cylinder operating.
‡ The operational pressure is the pressure range in which the motor or cylinders will operate.
‡ A much lower than normal bypass pressure could indicate a gear pump problem.
‡ If the bypass pressure remains the same after turning the function on, there could be a problem in
the control valve or circuit.