Nilfisk-Advance 56108110 SC8000 48 LPG, Руководство по обслуживанию

Страница: 103 / 225

n ine S ste 0 Service Manual – SC8000
n ine ir ilter Maintenance
Caution
:KHQVHUYLFLQJWKHHQJLQHDLU¿OWHUHOHPHQWVXVHH[WUHPHFDUHWRSUHYHQWORRVHGXVWIURP
HQWHULQJWKHHQJLQH'XVWFDQVHYHUHO\GDPDJHWKHHQJLQH
6HUYLFHWKHDLUFOHDQHUPRUHIUHTXHQWO\XQGHUVHYHUHGXVW\RUGLUW\FRQGLWLRQV
1. 5HPRYHWKHDLUFOHDQHUHOHPHQWVIURPWKHDLUFOHDQHUDVVHPEO\DQGLQVSHFWWKHPIRUIRUHLJQPDWHULDO
UHVWULFWLRQVRUVLJQVRIH[FHVVLYHZHDURUGDPDJH5HSODFHWKHHOHPHQWVLIQHFHVVDU\
5HPRYHDOOGXVWDQGIRUHLJQPDWWHUIURPWKHDLUFOHDQHUKRXVLQJ
3. 5HLQVWDOOWKHDLUFOHDQHUHOHPHQWV
5HLQVWDOOWKHDLUFOHDQHUFXSWKHQVHFXUHO\IDVWHQWKHUHWDLQLQJFOLSV
rou les ootin
7KH(&RQWUROVHQJLQHPDQDJHPHQWSDFNDJHVXSSRUWVUREXVWVHOIGLDJQRVWLFVDQGLVFDSDEOHRIVHWWLQJVFRUHV
RI'LDJQRVWLF7URXEOH&RGHV'7&V'7&VDQGVHQVRUGDWDFDQEHYLHZHGRQDFRSXWHUXVLQJWKH´*&3
'LVSOD\µVRIWZDUHDORQJZLWKDQ´(&RPµFRPPXQLFDWLRQFDEOH6HHWKH'LDJQRVLV0DQXDO(&06\VWHP
WG1605 9Y110-01760.pdf for the diagnostic tool connection procedure.
7KH(&RPFDEOHFDQEHSXUFKDVHGWKURXJK1LOÀVN$GYDQFH6HH6SHFLDO7RROVLQWKLVVHFWLRQIRUWKHSDUW
QXPEHU,WLVWKHVDPHFDEOHWKDWKDVEHHQXVHGRQRWKHUUHFHQW1LOÀVN$GYDQFHPDFKLQHVXVLQJWKH*0
/DQG*0/HQJLQHV<RXZLOOQHHGDQHZYHUVLRQRIWKH*&3VRIWZDUHWRZRUNZLWKWKH.XERWD
WG1605 engine along with the correlating password. The software, password and installation instructions
FDQDOOEHGRZQORDGHGIURP´&XVWRPHU=RQHµDWZZZDGYDQFHXVFRP
0RVWRUDOOHQJLQHWURXEOHVKRRWLQJLVFRYHUHGLQ.XERWDPDQXDOV7KHUHDUHVRPHWKLQJVVSHFLÀFWRWKH
SW8000 engine application which are covered here in this manual section such as, engine speed control and
engine starter operation.
Note: Refer to the 'LDJQRVLV0DQXDO(&06\VWHP:*<SGI , for engine
troubleshooting information and procedures including all fault code diagnosis.
eneral rou les ootin
Problem Cause Correction
The engine will not
crank. Weak battery, poor battery
cable connections.
‡
Check the battery and connections and clean/repair
as necessary.
‡
Check the wiring from the battery to the Starter B+
terminal on the A3 Engine System and repair as
necessary.
No power to the Starter
Solenoid (Starter Command
circuit)
‡
Make sure the foot pedal is in the neutral position.
‡
Reset the foot pedal deadband position if necessary.
(Refer to the
Control S ste Main Mac ine
Controller ro ra in section.)
‡
Make sure there is continuity through the Neutral
Relay K4 contacts 30 and 87a (relay off).
‡
Check the starter relay operation
‡
Check circuit breaker CB1 and reset if necessary.
‡
Check circuit breaker CB3 and reset if necessary.