Nidec NE200 Series Скачать руководство пользователя страница 71

Страница: 71 / 73

Trip

code

Trip Type

Possible causes

Solutions

error
2. EEPROM
damaged

2. Ask for service from
supplier

CCF

Keypad &
control board
communication
interrupted

1.Connection cable
between keyboard
and control panel is
broken

1. Check the connection
cable between keyboard and
control panel

bCE

Brake unit fault

1.The braking line or
braking pipe is
broken

1. Check the brake unit,
change the brake pipe.

2.brake resistor is
too lower

2. Choose the suitable
braking resistor.

PCE

Parameter copy
Error

1. Too long
connection cable
between keypad
and control board
leads to interference
in parameters
transmission.

1. Shorten the cable between
Keyboard and control board
to reduce interference.

2. The downloading
parameters do not
match the existed
parameters in the
inverter.

2. Before downloading, make
sure the parameters match
the inverter.

IDE

IDE Hall current
detection fault

1. The current
sensoring or hall
device get
damaged.

1. Ask for service from
supplier

ECE

③

Encoder fault

1. Encoder signal
wires are connected
reversely.

1. Check whether the
encoder signal is correctly
connected.

2. Encoder signal
wires get damaged.

2. Check whether the
encoder wiring is broke.

3. Encoder
damaged.

3. Change the encoder.

4. Dual-way
encoder detected
motor direction is
not match with

4. Change the encoder
direction (F3.16) or alter
motor wiring sequence.

Содержание NE200 Series










































































Результаты поиска

Содержание NE200 Series

Отзывы:

Похожие инструкции для NE200 Series

Бренды по названию

Популярные бренды

Nidec NE200 Series, Быстрый старт

Результаты поиска

Содержание NE200 Series

Отзывы:

Похожие инструкции для NE200 Series

Бренды по названию

Популярные бренды