Nice HySecurity SlideSmart DC Series Скачать руководство пользователя страница 60

Страница: 60 / 136

DISPLAY AND MENU OPTIONS

ENABLING THE FIRE DEPARTMENT
OVERRIDE

Many counties and cities require a Fire Department

override system for gate operators. The fire

department’s alert system is a separate unit that

must be connected to the Smart DC Controller.

The FIRE DEPARTMENT OPEN option must be

properly con

gured through the Installer Menu

before the operator will recognize the alert system.
To enable the Fire Department Override, take the

following steps and see Figure 54 and Figure 55:

Connect the NO contact from the alert system

or key switch to the following Smart DC

Controller terminals: EMERG OPEN and +24V.

Con

gure the Installer Menu. At a gate status

display, press the MENU button twice. This

accesses the User Menu and the CLOSE TIMER

display appears.

Simultaneously, press the OPEN and RESET

buttons to enter the Installer Menu. Release

the buttons and the USAGE CLASS display

appears. It is the

rst item in the Installer Menu.

Press NEXT until the FIRE DEPARTMENT

OPEN display appears. The factory default

setting is 0.

Use the NEXT button to change the number

on the display to 1 and then press SELECT.

To exit the Installer Menu, press the MENU

button. The gate status appears in the display

indicating you have returned to Run Mode.

Figure 54. Fire Department Override Connections

COM

STOP
OPEN

RADIO

OPEN

PARTIAL

EYE

OPEN

EYE

EXIT

LOOP

BLOCK

EXIT

IN OBS

LOOP

OUT OBS

LOOP

CENTER

LOOP

EDGE
EYE

COM
+ 24 V
EMERG

OPEN

SHOW

LEDs

FIRE

Figure 55. Fire Department Override Menus

CT 0 (OFF)
CLOSE TIMER

OPEN

STOP

RESET

SELECT

HYSECURITY
GATE CLOSED

OPEN

STOP

RESET

SELECT

1. Start at a gate

status display.

2. To access the

User Menu,

press the MENU

button twice.

3. Access the

Installer Menu, by

simultaneously,

pressing the

OPEN and

RESET

buttons.

4. Use NEXT to

navigate to the

menu display.

Change the

setting using the

SELECT and

NEXT buttons.

FO 1
FIRE DEPT OPEN

OPEN

STOP

RESET

SELECT

LL 0 (OFF)
LEARN LIMIT

OPEN

STOP

RESET

SELECT

hysecurity.com | 800-321-9947

SlideSmart DC Programming and Operations

Содержание SlideSmart DC Series









































































































































Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды

Nice HySecurity SlideSmart DC Series, Инструкция по установке и программированию

Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды