Nice HySecurity SlideSmart DC Series Скачать руководство пользователя страница 35

Страница: 35 / 136



Impediments to the sun’s rays reaching the

solar panels. Elements such as, shade, improper

alignment, or dirty panels will reduce the

amount of power available.



Extreme temperatures affect battery life. Keep

the batteries away from temperatures above

90°F (32°C). See "Important Considerations For

DC-Powered Operators" on page 39.



Good gate hardware and smooth, unobstructed

gate travel lowers the operator’s power draw

and serves to extend battery life.

NOTICE

Solar panels must not be shaded (not even

partially) or the output power will be signi

cantly

reduced. Panels must be kept clean as small

areas of sunlight blockage cause a large

reduction in output power. Alignment is also

critical because the rated wattage output is

based on the solar panels being mounted

perpendicular to the angle of the sun’s rays

midday on winter solstice (December 21st).

NOTICE

Any solar systems that are designed close to

the minimum margins will stress and shorten

the battery life and risk unreliable operation,

especially in periods of inclement weather.

CONNECTING THE SLIDESMART DCS TO
SOLAR POWER

Use 14 gauge wire or larger to connect the

solar panel(s) within 100ft of the operator.

Check NEC and local regulations if other

distances apply. See Figure 24.

Use one 24VDC solar panel or two 12VDC

solar panels in series with a total capacity of

at least 20W. Mount them according to the

manufacturer's installation instructions. See

Figure 24.

Figure 24. Solar Panels

Make sure both DC power switches on the

SlideSmart control box are in the OFF position,

and then remove the two Phillips head screws

that secure the 24VDC cover to the junction

box. See Figure 25.

Wire nut or crimp bond the solar panel wires

to the black and red input wires. See Figure 25.

Wire nut or crimp bond the equipment ground

wire to the green ground wire in the junction

box. See Figure 25.

Two 12V panels in
series connect to gate operator

12V

Minimum
10W Panel

Minimum
20W Panel

One 24V panel connects
to gate operator

Minimum
10W Panel

12V

24V

POWER

SlideSmart DC Programming and Operations

hysecurity.com | 800-321-9947

Содержание SlideSmart DC Series









































































































































Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды

Nice HySecurity SlideSmart DC Series, Инструкция по установке и программированию

Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды