Nice HySecurity SlideSmart DC Series Скачать руководство пользователя страница 56

Страница: 56 / 136

ADJUSTING GATE SPEED

The gate speed can be increased or decreased

a ¼ foot per second from the operator’s default

speed. See Figure 49

To adjust the gate speed, take the following steps:

At a gate status display, press the MENU button

twice. The CLOSE TIMER display appears.

Simultaneously, press the OPEN and RESET

buttons to enter the Installer Menu. Release

the buttons and the LEARN LIMITS display

appears. It is the

rst item in the Installer Menu.

Press NEXT until the OPEN SPEED (or CLOSE

SPEED) display appears. Select the desired

setting based on the operator type:

SlideSmart DC 15

0 = 0.75 ft/s

1 = 1.0 ft/s

(Usage Class 3 & 4 only)

2 = 1.25 ft/s

SlideSmart DC 10F

4 = 1.75 ft/s

(The DC 10F is designed for

Usage Class 3 & 4 sites only)

5 = 2.0 ft/s

6 = 2.25 ft/s

Use the SELECT and NEXT buttons to navigate

and change the speed setting on the display.

To exit the Installer Menu, press the MENU

button. The gate status appears in the display

indicating you have returned to Run Mode.

NOTICE

Two options, one for OPEN SPEED the other

for CLOSE SPEED, appear in the Installer

Menu. The steps involved in changing the

open speed are shown below. The steps to set

the close speed are the same, you just need

to access the CLOSE SPEED option.

NOTICE

Certain speeds are allowed only when the

operator’s Usage Class is set appropriately.

Figure 49. Adjusting Gate Speed

CT 0 (OFF)
CLOSE TIMER

OPEN

STOP

RESET

SELECT

HYSECURITY
GATE CLOSED

OPEN

STOP

RESET

SELECT

1. Start at a gate

status display.

2. To access the

User Menu,

press the MEN

button twice.

3. Access the

Installer Menu,

simultaneously,

pressing the

OPEN and

RESET

buttons.

4. Use NEXT to

navigate to the

menu display.

Change the

setting using th

SELECT and

NEXT buttons.

OS 5
OPEN SPEED

OPEN

STOP

RESET

SELECT

LL 0 (OFF)
LEARN LIMIT

OPEN

STOP

RESET

SELECT

DISPLAY AND MENU OPTIONS

hysecurity.com | 800-321-9947

SlideSmart DC Programming and Operations

Содержание SlideSmart DC Series









































































































































Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды

Nice HySecurity SlideSmart DC Series, Инструкция по установке и программированию

Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды