Nice HySecurity SlideSmart DC Series Скачать руководство пользователя страница 27

Страница: 27 / 136

ESTABLISHING THE OPEN & CLOSE LIMITS

After programming the initial setup menus, the

operator needs to establish the OPEN and CLOSE

limits.
The LEARN LIMITS display automatically appears

after you set the gate weight. To set the open and

close limits, take the following steps:

Hold the OPEN button until the gate slides

to full open. Release the OPEN button. Note

that if you go too far, you can press CLOSE to

reverse direction. Press STOP twice to store

the open stop location in memory.

Hold the CLOSE button until the gate slides to

full close. Release the CLOSE button and press

STOP twice. The full close stop is retained in

memory.

GATE CLOSED appears on the display and

ALERT 15

ashes until the target magnet is

installed and its location stored in memory. See

"Installing the Target Magnet" on page 28.

Once the target is installed, SlideSmart never

forgets its limits. AC or DC power can be lost and

SlideSmart always remembers where to stop the

gate within a ¼-inch of its established limit. The

only exception occurs when a chain is replaced

or damage occurs to the operator itself. To reset

limits, see "Resetting the OPEN and CLOSE

Limits" on page 55.

NOTICE

Do not set limits at the physical OPEN and

CLOSE stops. Leave a 1 to 2-inch (2.5 - 5cm)

gap to allow some slack and give in the chain.

This will help prevent chain wear and avoid

stress on gate hardware.

NOTICE

Pressing OPEN will reverse direction.

NOTICE

NO AC POWER

ashes after the gate status

display if the AC power has not been connected

or the lower power switch is turned off.

INSTALLATION

Figure 17. Programming Learn Open

CAUTION

Do not install the target magnet before setting

the OPEN and CLOSE limits. If the target

magnet is installed before setting the limits, the

target magnet can get wound around the roller

sprocket which will damage the SlideSmart

operator and void the Limited Warranty.

LEARN OPEN
INCHES: +XXX.X

OPEN

STOP

RESET

SELECT

LEARN CLOSE
INCHES: - XXX.X

OPEN

STOP

RESET

SELECT

HYSECURITY
GATE CLOSED

OPEN

STOP

RESET

SELECT

SlideSmart DC Programming and Operations

hysecurity.com | 800-321-9947

Содержание SlideSmart DC Series









































































































































Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды

Nice HySecurity SlideSmart DC Series, Инструкция по установке и программированию

Результаты поиска

Содержание SlideSmart DC Series

Отзывы:

Бренды по названию

Популярные бренды