NF CA5350 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 110

background image

CA5350

iii

WARNING



Do not remove the cover.

This product contains high-voltage parts. Absolutely never remove its cover. Even when
the inside of this product needs to be inspected, do not touch the inside. All such
inspections should be performed by service technicians designated by NF Corporation.



Do not modify this product.

Absolutely never modify this product, as this may cause new hazards and may
disqualify this product from repair in case of failure.



Ensure that water does not get into this product or it does not get wet.

Using the product in wet condition may cause electric shock and fire. When water etc.
get into the product, immediately pull out the power supply cord, and contact

NF

Corporation or one of our representatives

from where you bought the product.



In the event of thunderstorm in the nearby area, turn off the power supply switch, and
pull out the power supply cord.

Thunderstorm may cause electric shock, fire, and breakdown.



Safety-related symbols

The general definitions of the safety-related symbols used on this product and in the
instruction manual are provided below.

Instruction Manual Reference Symbol

This symbol is displayed to alert the user to potential danger and
refer him/her to the instruction manual.

Electric Shock Danger Symbol

This symbol indicates locations that present a risk of electric
shock under specific conditions.

Warning Symbol

This symbol indicates information for the avoidance of a hazard such
as electric shock that may endanger human life or cause serious injury
during handling of the equipment.

Caution Symbol

This symbol indicates information for minor or moderate injury, or
property damage to the equipment during handling.

●

Other Symbols

This symbol indicates the “on” position of the power switch.

This symbol indicates the “off” position of the power switch.

This symbol indicates that external conductor of the connector is
connected to the case.

This symbol indicates that the external conductor of connector is
connected to the signal ground.

CAUTION

«
...
5
6
7
8
9
...
»

Содержание CA5350















































































































Отзывы:

Нет отзывов

Похожие инструкции для CA5350

Бренд: NAD Страницы: 70

Бренд: DAD Страницы: 24

Бренд: dB Страницы: 6

Super Blue PB559X

Бренд: Pyramid Страницы: 12

Strain Gauge/Load Cell Bridge Amplifier FBDA

Бренд: B&B Electronics Страницы: 10

Бренд: JBL Страницы: 17

Бренд: JDS Labs Страницы: 7

Бренд: Parasound Страницы: 16

Claymount AmpMC 3-field Series

Бренд: Varex Imaging Страницы: 24

Бренд: NAD Страницы: 2

Бренд: OPTEX FA Страницы: 5

Бренд: Orion Страницы: 21

Pro-linebacker PL50R

Бренд: Laney Страницы: 2

Бренд: Kobble Digital Electronic Страницы: 10

Бренд: Acoustic Страницы: 8

Бренд: VINTAGE SOUND AMPS Страницы: 9

Бренд: Xantech Страницы: 20

Бренд: Kicker Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды