NF CA5350 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 110

background image

CA5350

ii

―――

Safety Precautions

――

―

To ensure safe use, be sure to observe the following warnings and cautions.
NF Corporation shall not be held liable for damages that arise from a failure to observe
these warnings and cautions.
This product is a Class I product (with protective conductor terminal) that conforms to the
JIS and IEC insulation standards.



Be sure to observe the contents of instruction manual.

This instruction manual contains information for the safe operation and use of this
product.
Be sure to read this information first before using this product.
All the warnings in the instruction manual must be heeded to prevent hazards that
may cause major accidents.



Be sure to ground the product.

To prevent electric shock, be sure to safety implement grounding such that ground
resistance is 100Ω or lower.
This product is automatically grounded when its three-pin power supply plug is
connected to the power outlet with a protective-ground contact.
When using a three-pin to two-pin conversion adapter, be sure to connect the grounding
wire of the adapter to the grounding terminal next to the outlet.



Check the power supply voltage

This product operates under the power supply voltage indicated in “Grounding and
Power Supply Connection” in this instruction manual.
Before connecting the power supply, check that the voltage of the power supply matches
the rated power supply of this product.



Observe the fuse rating

Using an unspecified fuse could cause a fire. Use the rated fuse specified in “Grounding
and Power Supply Connection” of the instruction manual.
Also, when replacing the fuse, the power cord must be disconnected from the power
outlet.



In case of suspected anomaly

If this product emits smoke, an abnormal smell, or abnormal noise, immediately power
it off and stop using it.
If such an abnormal occurs, prevent anyone from using this product until it has been
repaired, and immediately report the problem to NF Corporation or one of our
representatives.



Do not use this product when there is gas around.

An explosion or other such hazard may occur.

«
...
4
5
6
7
8
...
»

Содержание CA5350















































































































Отзывы:

Нет отзывов

Похожие инструкции для CA5350

Bassman Bassman 100

Бренд: Fender Страницы: 20

Бренд: Fender Страницы: 156

G-DEC 3 Thirty & Fifteen

Бренд: Fender Страницы: 24

Бренд: Randall Страницы: 12

Бренд: ZeeVee Страницы: 44

Бренд: Zed Audio Страницы: 44

Бренд: B&K Страницы: 64

Бренд: Bad Cat Страницы: 7

Бренд: Channel D Страницы: 8

Power Amplifier Servo 120

Бренд: Samson Страницы: 13

Бренд: Viking Страницы: 4

Бренд: DaytonAudio Страницы: 2

Бренд: Lanzar Страницы: 13

Бренд: Akai Страницы: 21

Wireless2100-System

Бренд: MultiChannel Страницы: 43

HD-AMP1/U1B/K1B/FN

Бренд: Marantz Страницы: 99

Бренд: PBN Страницы: 32

Бренд: SPITFIRE AUDIO Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды