manualshive.com logo in svg

Next NI400, Руководство пользователя, Страница: 56 / 59

Поделиться
Скачать
Next NI400 Скачать руководство пользователя страница 56

0110

 www.ruggedaq.com

DETAILED 

SPECIFICATIONS

NI400

0111

 www.ruggedaq.com

11

DETAILED 

SPECIFICATIONS

NI400

11

CPU AND MEMORY

Processor

ARM Cortex - M3 MCU with 1 MB Flash, 20 MHz CPU, ART Accelerator

RAM Memory

128 Kbyte internal RAM

Mass storage

SD CARD 2 GB for data (about 5 Mega data points) and WEB pages

Clock accuracy

High precision RTC (real time  clock with battery back-up)

On-board sensors

Temperature measured on the electronic board

NI400

Case and Protection

IP67

3G

Y

Relay Output (30V 2A)

1

Analog Input Number

4

Voltage

Y

Current

Y

mV/V

Y

Vibrating Wire

Y

PT100 - NTC

Only NTC

Thermocouple

Y

Switchable Power supply

(selectable by the software): 24 V, 12 V, 5 V

Y

RS485

1

Power Supply RS485

Y

Display

7 segment

USB HOST

Y

PC Connection with USB

Y

Relè Protection/Gas Discharge

Y

Memory

2GB

Software Web Server

Y

Cloud Dashboard Management

Y

INPUT

Analog differential 

inputs     

 

4 differentials channels, individually configured at factory, according to 

the following sensors:
- Thermocouples
- Vibrating Wire + Thermistor (NTC)
- Thermistor (NTC)
- 4-20 mA current loop (2 wires)
- 4-20 mA (3-4 wires)
- Voltage (4 wires)
- Wheatston bridge (6 wires, utilize No. 2 channels)

INTERFACES

Display & 

Keyboard

7 segment LED display and two selection keys for the minimal local 
management without PC:
device status, data download and FW/web pages update by USB pen 
drive

USB Host

USB 2.0 full speed (Type A connector) 5V, max 500 mA, pen drive only 
(FAT 16 or FAT 32)

USB Device

USB 2.0 full speed (Mini B connector) 5V, max 500 mA, PC connection only

Modbus RTU 

sensor slave 

RS485

5 screw clamp port for max. No.64 Modbus digitized sensors.
Communication interface: RS485
Communication protocol: MODBUS RTU
The voltage ‘V OUT’ is switched on and off from the software. V OUT is 
the unregulated power supply input ‘V IN’ (1 A)
Power supply management (always on or energy safe)

WIRELESS

3G

Integrated SIM holder Extended temperature range (-40° to 85°C).
Stubby antenna with SMA connector

EUD

NAD

BRAZIL

UMTS ǀ HSPA BANDS (MHz)

 900 / 2100

850 / 1900

 850 / 2200

GPRS ǀ EDGE BANDS (MHz)

900 /1800

850 / 1900

 850 / 900 / 

1800 / 1900

Содержание NI400




























































Отзывы:

Нет отзывов