background image

5/10 - Safety instructions and user guide for the automatic pool cover

This document is the property of AS POOL - NextPool group and cannot be reproduced or communicated without our authorisation.

5

• 

Do not operate the cover more than 15 consecutive 

minutes. 

• 

It is prohibited to manoeuvre the cover if there is a 

load  on  the  duckboard  walkway  of  an  submerged 

cover, this might cause the cover to scrape the beam.

• 

Prohibit an overload on the duckboard walkway for 

an submerged cover due to the physical limits of the 

beam  and  the  fixtures.  The  duckboard  walkway  is 

supported by the pool edge and the beam, and is 

designed to support a maximum load of 400 kg over its 

complete length (duckboard included) and 150 kg per 

linear metre.

• 

Do not walk or jump on the covering of the BANC roller 

in order to avoid deforming it.

• 

It is essential, for safety reasons, to remove the key 

from the control box or the manual wheel, or to close 

the  Aero  application  once  the  opening  or  closure 

actions are complete.

• 

Programme the filtering system to start as soon as the 

"solar" slats are in sunlight. During very sunny periods 

with the cover closed, the water temperature can 

reach 30° or more and can damage the slats.

• 

It is strongly recommended not to empty the pool 

without the authorisation of your installer.

• 

If the cover is fitted with a WING System

®

, take care not 

to operate the cover without having folded the WING 

System

®

 onto the cover. Operating the cover with the 

WING System

®

 deployed can cause major damage to 

the cover and the pool. 

• 

If the cover is fitted with a SURF System (mobile roller), 

two people are required to move the roller. Make sure 

the roller is correctly positioned on the pool before any 

automatic action of the slats.

• 

In  the  case  of  an  emergency  operation,  a  person 

walking on the cover will have his/her feet under the 

water.

• 

Limit  operating  the  slatted  cover  when  the 

temperature  is  below  5°C  and  do  not  handle  the 

cover below 0°C when it is locked in ice. Avoid all 

impacts and mechanical contacts on the slats when 

the temperature is below 0 °C.

• 

When the cover is installed on a sheltered pool, make 

sure that the air temperature is no higher than 40 °C. 

Make sure that the surrounding air is ventilated in 

order to avoid all distortions and deteriorations of the 

parts (PVC slats, bench panels, duckboards, etc.).

• 

Regularly remove any debris from the slat cover. They 

will thus prevent rolling it in with an accumulation of 

leaves or debris that could cause brownish stains to 

appear on the slats. This natural phenomenon is not 

covered by our guarantee.

3. 

Advice for use

• 

Always  check  that  the  pool  water  level  remains 

constant and in compliance with the manufacturer's 

recommendations  (-12  cm  as  a  standard)  before 

using the cover in order to avoid jamming the slats in 

the trench (against the beam or the partition wall), 

or to prevent them from rubbing against the pool 

copings, or to avoid the slats being warped by excess or 

insufficient water levels. Make sure that the overflow 

and the water level regulator are operational so that 

the skimmers do not suck in air if the water level is too 

low.

• 

Remove  all  floating  objects  that  could  hinder  the 

correct operation of the ABRIBLUE cover during its 

closure, and lock the access to the pool using the 

blocking straps.

• 

Do not forget to unlock the safety mechanisms before 

opening the pool cover as failure to do so may damage 

the pool cover.

• 

Always keep the pool in full view during the opening 

and  closing  operations.  It  may  be  necessary  to 

accompany  the  cover  manually  during  rolling  or 

unrolling operations in order to position it correctly if 

there is a strong side wind, a free form pool, or a pool 

with a specific configuration.

• 

It is imperative not to halt the cover in an intermediate 

position, this can cause the risk of jamming a bather's 

body at the level of the cover casing, if a bather uses 

the pool. The person carrying out the action must 

make sure there are no bathers in the pool before 

starting.

• 

Check that the hose or power supply cable of the pool 

cleaner does not get tangled in the cover; this could 

jam the operation of the roller and damage the PVC 

slats.

• 

Check that unrolling and rolling runs correctly over the 

first few metres (the slats roll effortlessly, there is no 

jamming on the shaft with the top "bulging" towards 

the outside of the roll), and if necessary, stop the 

action immediately in order to intervene on the cause 

of the malfunction. 

• 

The rotational speed of the shaft is not constant due to 

the rolling/unrolling of each new layer of slats which 

unbalances the roller. Adapt the wheel's rotational 

speed on the manual model in order to avoid the 

harder spots by handling the wheel with both hands. 

• 

It is imperative during rolling or unrolling operations, 

not to release the control until the limit switches have 

been reached (especially on the BANCS) in order to 

correctly position the slats on the roller when rolling 

in  is  complete,  or  on  the  water  when  unrolling  is 

complete.

• 

On the model without limit switches, make sure not 

to roll-in the slats too much in order to prevent them 

from falling to the rear and breaking. 

Содержание ABRIBLUE BANC D.SIGN



































Отзывы: