background image

19/24 - Installation instructions for the BANC D.sign above water automatic slatted safety cover

19

13.6  Checking the electronic board and 

communications

13.6.1 Power on the control box and check that the board 

is powered on.

13.6.2 Check that "led1" indicator on the electronic board 

is on.

13.6.3 Measure 24 V on the "+" and "-" terminals of the 

electronic board.

-

Check  that  the  Bluetooth  LED  is  flashing  blue 

(if the led flashes twice, it means the electronic 

board is paired with a terminal).

-

Check  that  the  orange  relay  LEDS  light  when 

opening and closing using the mobile app.

-

Powering off the control box cuts the Bluetooth 

signal  and  allows  the  electronic  board  to  be 

reinitialised at all times.

-

Check the board electric connections using the 

attached drawings.

-

Check the following terminal blocks:

-

"TCTC" wires 1 and 2 on the T terminals and C 

terminals connected to + wires. -"BP" must be 

connected to the push button.

-

"+WBGR"  check  that  the  wires  are  the  same 

colours as the LEDs (terminal W should be free).

13.7 Bluetooth pairings

-

If pairing the phone with the board is impossible, 

reinitialise the board.

-

Press;PRG1 (for about 12 seconds) until all the 

LEDs light, and then while the red>orange>green 

and the two relay LEDS each flash in turn.

-

When this step is complete, the board has the 

factory settings applied (green LED on).

-

Then repeat the pairing procedure described in 

section 4.5.3.

14. Checks

Check the following points relating to the NF P 90-308 

standard and check that the cover operates correctly:

-

When turning the key switch for the cover, the 

entire pool is visible and check that there are no 

bathers in the pool when closing the cover. The 

unrolling operation stops when the key is released. 

The key can be removed from the control box.

-

The cover rolls and unrolls correctly.

-

The  safety  mechanisms  are  easily  handled  for 

the recommended water levels and are sufficient 

(number and position). Check that they are locked 

on completion of the installation.

-

The gaps along the length between the slats of the 

apron and the pool wall are less than 7 cm and the 

apron does not rub "abnormally" against the wall.

-

The  space  between  the  bottom  of  the  bench 

(beam) and the water is less than 15 cm on the 

swimming pool side.

-

The  space  between  the  bottom  of  the  bench 

(beam) and the pool deck is less than 10 cm on the 

rear pool deck side.

-

The voltage powering the cover is less than 30 V 

DC.

-

The limit switches are operational.

-

The site is cleaned after installation of the cover 

and the packaging and waste is removed.

-

"Waste Electric and Electronic Equipment" (WEEE) 

is the subject of specific collection. It should not be 

disposed of with your unsorted household waste.

15.  Receipt of the slatted 

cover by the end customer

-

The installer explains the operation of the ABRIBLUE 

cover to the end user and informs him/her of the 

safety, usage, upkeep and winterisation advice.

-

They give them the cover instructions: "Installation 

instructions" and "Safety instructions and user guide 

for the automatic cover".

-

They demonstrate the use of the cover and explain it 

functional limits.

-

The installer and end user fill in and sign the guarantee 

form attesting to the compliance of the installation, 

the reception of the documents for the cover and the 

information given to the end user featured in the cover 

safety instructions.

Содержание ABRIBLUE BANC D.SIGN



































Отзывы: