NETGEAR JNR1010v2 Скачать руководство пользователя | Manualshive

Страница: 88 / 91

background image

Troubleshooting

88

JNR1010v2 N150 Wireless Router

•

Check that your computer has the IP address of your router listed as the default gateway.
If a DHCP server assigns the IP configuration of your computer, this information is not
visible on your computer’s Network Control Panel. Verify that the IP address of the router
is listed as the default gateway.

•

Check to see that the network address of your computer (the portion of the IP address
specified by the subnet mask) is different from the network address of the remote device.

•

Check that your cable or DSL broadband modem is connected and functioning.

•

If your ISP assigned a host name to your computer, enter that host name as the account
name in the Internet Settings screen.

•

Your ISP might be rejecting the Ethernet MAC addresses of all but one of your
computers.

Many broadband ISPs restrict access by allowing traffic only from the MAC address of your
broadband modem, but some ISPs additionally restrict access to the MAC address of a
single computer connected to that modem. If this is the case, configure your router to clone or
spoof the MAC address from the authorized computer.

«
...
86
87
88
89
90
...
»

Содержание JNR1010v2




























































































Отзывы:

Нет отзывов

Похожие инструкции для JNR1010v2

Бренд: Icom Страницы: 2

Бренд: Raymarine Страницы: 20

iB-WRX150NE Baton

Бренд: iBall Страницы: 102

Бренд: Mixcder Страницы: 75

JBL Under Armour SPORT WIRELESS FLEX

Бренд: Harman Страницы: 24

Бренд: EnGenius Страницы: 5

Бренд: PROception Страницы: 13

Бренд: sauter Страницы: 8

Бренд: Binatone Страницы: 14

Бренд: 4IPNET Страницы: 194

Бренд: UniFi Страницы: 45

Бренд: D-Link Страницы: 101

Бренд: Planet Networking & Communication Страницы: 2

RTA2600 HighPower

Бренд: Amped Wireless Страницы: 2

Бренд: Amped Wireless Страницы: 2

TITAN-AP APA1900

Бренд: Amped Wireless Страницы: 78

Бренд: EnGenius Страницы: 80

Бренд: LogiLink Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды