NETGEAR JNR1010v2 Скачать руководство пользователя

Страница: 59 / 91

Advanced Settings

JNR1010v2 N150 Wireless Router

Click the

Apply

button.

Your changes are saved.

Enable or Disable Wireless Router Radio



To enable or disable the wireless router radio:

For more information, see

Log In to Your Router After Installation

on page

18.

Select

ADVANCED > Advanced Setup > Advanced Wireless Settings

The following screen displays:

Do one of the following:

•

To turn on the wireless radio, select the

Enable Wireless Router Radio

check box.

•

To completely turn off the wireless radio of the router, clear the

Enable Wireless

Router Radio

check box.

When the wireless radio is disabled, you can still use the router by connecting
computers to the router with an Ethernet cable. By default, the wireless radio is
enabled.

Click the

Apply

button.

Your changes are saved.

Содержание JNR1010v2




























































































Результаты поиска

Содержание JNR1010v2

Отзывы:

Похожие инструкции для JNR1010v2

Бренды по названию

Популярные бренды

NETGEAR JNR1010v2, Руководство пользователя

Результаты поиска

Содержание JNR1010v2

Отзывы:

Похожие инструкции для JNR1010v2

Бренды по названию

Популярные бренды