NETGEAR DG834G v5 Скачать руководство пользователя страница 60

Страница: 60 / 157

Wireless ADSL2+ Modem Router DG834Gv5 User Manual

4-7

Managing Your Network

v1.0, March 2010

Viewing Connection Status

Click the

Connection Status

button on the Router Status screen to view the connection status:

Table 4-2. Router Statistics Fields

Field

Description

WAN (Internet),
LAN, or WLAN
(Wireless LAN)
statistics

Status

The link status of the port.

TxPkts

The number of packets transmitted on this port since reset or
clear.

RxPkts

The number of packets received on this port since reset or
clear.

Collisions

The number of collisions on this port since reset or clear.

Tx B/s

The average egress line utilization for this port.

Rx B/s

The average

ingress line utilization

for this port.

Up Time

The time elapsed since the last power cycle or reset.

ADSL Link
Downstream or
Upstream
These statistics
might help your
technical support
representative if
there is a connection
problem.

Connection Speed

Typically, the downstream speed is faster than the upstream
speed.

Line Attenuation

The line attenuation increases the further you are physically
located from your ISP’s facilities.

Noise Margin

This is the signal-to-noise ratio and is a measure of the quality
of the signal on the line.

Poll Interval

Specifies the interval at which the statistics are updated in this
window. Click

Stop

to freeze the display.

Figure 4-5

Содержание DG834G v5






























































































































































Результаты поиска

Содержание DG834G v5

Отзывы:

Похожие инструкции для DG834G v5

Бренды по названию

Популярные бренды

NETGEAR DG834G v5, Руководство пользователя

Результаты поиска

Содержание DG834G v5

Отзывы:

Похожие инструкции для DG834G v5

Бренды по названию

Популярные бренды