Neatech EVO3 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 93

Neatech EVO3 Скачать руководство пользователя страница 9

www.neatech.it

9

1

WHEELCHAIR PRESENTATION

Thank you for purchasing EVO3 electronic wheelchair.
EVO3 is a battery powered wheelchair. Its intended use is to provide indoor mobility to person
limited to seated position that are capable to operate and drive an electronic wheelchair.
Though EVO3 was designed to be used mainly indoors it is possible to have lights and to use the
wheelchair even in some outdoor environments.

Motors

2x 220 W

Batteries

2x55Ah 12V

Electronic Tilt (45°) + Electronic Negative Tilt (45°)

Electronic Lift (30 cm)

Electronic Reclining Backrest (0-170°)

Electronic Elevating Central Mounted Footrest

WARNING:

It is prohibited to use wheelchair or its parts for any

purpose other than that indicated. For a correct use please follow
the instructions given in this manual.

NEATECH.IT disclaims

any responsibility for damages caused by improper use of

aids.

The information in this manual may be subject to change without

notice. All information, pictures and specifications are based
upon the product information that was available at the time of

printing. They are representative examples and not intended to
be exactly as the actual wheelchair

«
...
7
8
9
10
11
...
»

Содержание EVO3






























































































Отзывы:

Нет отзывов