manualshive.com logo in svg

Neatech EVO3, Руководство по обслуживанию, Страница: 76 / 93

Поделиться
Скачать
Neatech EVO3 Скачать руководство пользователя страница 76

 

www.neatech.it 

76 

BACKREST 

UP:  

Move  the  backrest  UP  till  the  angle  of  backrest  is  more  than  a 

customizable value. 

DOWN: 

Move  the  backrest  down  till  the  angle  of  backrest  is  less  than  a 

customizable value. 

 

The  angle  of  the  backrest  is  calculated respect the  chassis  inclination, not respect  the 

seating inclination. 

The parameter PG1 sets the maximum angle of the backrest. The range is 150°-165°. It 

must be greater than the parameter PG4. Default value is 165°. 

The  parameter PG4  sets  the  minimum angle  of  the  backrest. The  range  is 90°-125°. It 

must be less than the parameter PG4. Default value is 90°. 

 

 

Figure 84 

LEGREST 

UP: 

Move the legrest UP till the legrest is parallel to the direction of the 

chassis. 

DOWN: 

 

Move the legrest DOWN till there are danger crash into the chassis 

 

During both  UP  and DOWN  function the  system checks  for the  presence  of  danger of 

crash into the floor. In case of danger the seat will lift up before move the legrest. 

The angle of legrest is measured respect the inclination of the chassis, not respect the 

seating inclination. 

The parameter PG2 sets the minimum inclination of the legrest to avoid crash into the 

chassis.  

Default value is 90°. 

90 °

Chassis Orientation

Chassis Orientation

180 °

Содержание EVO3






























































































Отзывы:

Нет отзывов