![background image](http://html1.mh-extra.com/html/national-instruments/ni-dids-2103/ni-dids-2103_user-manual_3423830176.webp)
176 | ni.com | NI DIDS-2100 Series User Manual
Detail: When
ON
, operating points are active according to the operating point table, and the table values
will override the parameter values specified elsewhere within the DI Driver System setup windows. When
OFF
, the parameter values will remain set to the most recent values used from the operating point table. For
example, HVTarget for DI Driver Module 1 may be set to 50V via the
Setup window may implement a time-based table for incrementing HVTarget by 10V every 10 seconds, from
50V to 100V. At the end of the operating point cycle, HVTarget will be left at the last operating point of 100V.
If it is desired that HVTarget be set back to 50V, then an additional operating point should be added to the
end of the table to revert back to 50V.
Pause OP
Tip Strip: In
pause operating point execution
Detail: When
ON
, pauses the table to remain at the current operating point. When
OFF
, operating point
operation resumes. This parameter is only applicable when
ON
.
Reset OP
Tip Strip: In
reset operating point execution to point 0
, when
ON
, resets the operating point back to zero. This parameter is not applicable to
. This parameter is only applicable when
is
ON
.
Manually Set OP
Tip Strip: Causes execution of Manual OP
Detail: When
ON
, sets the operating point to the point specified by the value to the left of the button. In
OFF
execution will resume at the current operating point. In
, when set to
OFF
execution will resume at the operating point determined by the
Process Variable Trigger Wildcards
Number of OP
Tip Strip: Number of operating points to be considered for execution
Detail: Specifies the number of operating points to be considered by the operating point function. For
example, if
is set to 3, then operating points 0, 1, & 2 will be applicable to the function.
Operating points 3 and greater will not be considered.
Error OP
Tip Strip: Operating point executed during error state
Содержание NI DIDS-2103
