15
[22]Miscellaneous Features 1
(1) Abort Delay
- Program to allow a 15
second Delay (except
24 Hour Zones
) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent
reporting.
(2) Easy Exit/Easy Arm
- Enables
A
0
command. While the system is armed,
entering this command allows 3 minutes to
Exit through
Exit/Entry
and
Exit/Entry
Follower Zones
. Enabling this option also
enables Easy Arm, enter
a
0
to arm
the system.
(3) Swinger Shutdown
- Automatically
disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour
Protection zones: allows only 3 alarms and
2 restores per zone per arming before the
zone is disabled.
(4) Bell on Line Cut
(Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23]Programmable Output Features 1
(1) Audio Verification
- Program to activate
the PGM during reporting. Select specific
zones for audio verification by programming
the required zones in
PGM Output
[08],
PGM Features 2
[24] and
PGM Features 3
[25]. Connect the PGM to the Veriphone
TM
trigger low input.
(2) Access Output
- Activates the PGM
output for 5 seconds using the
A
3
command.
(3) Follow Keypad Sounder
- The following
keypad sounds will activate the PGM output:
Entry Sounder, Keypad Pulsing Sounder,
Keypad Output on Alarm, Chime, Fault Find.
(4) Keyfob/Keyswitch Chirp
- Program to
chirp the PGM Output (1) one time when the
panel is armed or (2) two times when the panel
is disarmed. Wire as shown in Figure 7.
[24]Programmable Output
Features 2
(1)
I
Fire
- Program to activate the PGM
on a Fire alarm.
(2) AUX
- Program to activate the PGM on a
AUX alarm.
(3) Panic
- Program to activate the PGM on
a Panic alarm.
(4) Test Timer
- Program to activate the
PGM during a Test Timer report.
[25]Programmable Output Features 3
(1)
Y
AC Fail
- Program to activate the
PGM on the loss of AC. (15 minute delay)
(2) Low Battery
- Program to activate the
PGM on a Low Battery condition.
(3) *Trouble
- Program to activate the PGM
on a Trouble condition.
(4) Armed
- Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*
Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper,
Receiver JAM, Wireless Smoke Low
Battery, Wireless Smoke Supervisory Fail.
[26]Miscellaneous Features 2
(1) Momentary Keyswitch Arming
-
Typically, connect a normally-open
Keyswitch across the zone AND its 3.3K
zone-doubling resistor.
(2) Reserved
.
(3) Inhibit Fail-to-Communicate Display -
This option prevents the keypad from either
indicating or sounding when a Fail to
Communicate has occurred.
(4) Inhibit Low Battery Display
- Program
to inhibit the Low Battery Display at the
keypad. Low Battery Reporting is not
inhibited. The programming option is not
permitted for UL installations.
Telephone Number 1 Programming
[30]Subscriber ID Number
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
N/O
N/C
COM
BLK
RED
+AUX
Siren Driver
Steady Input
PGM
+AUX
K1
FIGURE
7
K
EYFOB
/K
EYSWITCH
