NAPCO Gemini GEM-P816, Инструкция по программированию

Страница: 28 / 56

GEM-P816 Programming Instructions
Page 28
NAPCO Security Systems
R
TEMPERATURE DISPLAY AT KEYPAD (ADDRESS 1666-1668)
Temperature Display at Keypad
The temperature is displayed instead of the date on line 2 of the GEM-RP1CAe2 (or GEM-K1CA) keypad. The keypad will display
from –22F to 140F (or -30C to 60C). Fahrenheit is the default setting, select Celsius by enabling address 1668 option 2. When this
Temperature Display Option is enabled, Zone 6 becomes the input for the GEM-TEMP64 Temperature Sensor module and Zone 6
of the panel becomes inoperative.
Address 1668 option 3 enables Zone 6 to report a temperature problem. Address 1666 (options 1-7) set the lower limit temperature
value and address 1667 (options 1-7) sets the upper limit temperature value (both values are set in binary). If the temperature de-
tected by the panel is above or below these set limits, the panel will report an alarm on Zone 6. To function and report properly,
Zone 6 must be selected as a reporting zone, 24hr zone in area 1 and auto-resetable. At both 1666 and 1667 addresses, option 8
sets positive or negative temperature. If the temperature of 0 degrees is required, "negative zero" (-0) degrees must be used (+0 or
an empty location is not a valid temperature). To simulate the sensor module, a power supply can be connected to Zone 6 and set
from .55v to 3.05v to display the whole temperature range. Temperature values are read and updated every 5 seconds. To report
an outer limit temperature, the temperature must be out of limits for 2 seconds. To avoid false alarm reports, the limits have a
threshold of 5 degrees in the software. Two new logs have been created for temperature out of limits and restore. If the
G
key
is depressed and held down for 2 seconds, the date will display for 5 seconds.
In addition, three addresses must be enabled (either via Quickloader or via direct address programming) in order for the
Tempera-
ture Display at Keypad feature to operate.
The following features must be enabled In Quickloader (or in direct address programming):
1. Keypad Assignment , Temperature Settings tab, Enable Temperature Display (Address 1668, option 1)
2. Keypad Assignment , Keypad Features tab, Enable Keypad Time/Date Display (Address 1420, option 7)
3. Keypad Assignment , Keypad Features tab, Enable Set Time/Date Message (Address 2051, option 1)
Note: If these three addresses are set and power (AC and battery) are subsequently removed, they keypad will indicate that the
time and date are lost and will need to be reset. See WI1425 for more information.
1668
Default
Option
OFF
1 Enable Temperature Display Option
OFF 2
Select Degrees Celsius
OFF
3 Report Temperature Alarm (Zone 6)
OFF 4
Reserved
OFF 5 Reserved
OFF 6 Reserved
OFF 7 Reserved
OFF 8 Reserved
Enable Temperature Options
‡
1666
Default
Option
OFF 1 Binary Temperature Value 1°
OFF
2 Binary Temperature Value 2°
OFF 3
Binary Temperature Value 4°
OFF
4 Binary Temperature Value 8°
OFF
5
Binary Temperature Value 16°
OFF 6 Binary Temperature Value 32°
OFF 7 Binary Temperature Value 64°
OFF
8
Enable for Negative Temperature Value
Temperature Lower Limit
‡
1667
Default Option
OFF
1 Binary Temperature Value 1°
OFF 2
Binary Temperature Value 2°
OFF
3 Binary Temperature Value 4°
OFF
4 Binary Temperature Value 8°
OFF 5 Binary Temperature Value 16°
OFF 6 Binary Temperature Value 32°
OFF
7
Binary Temperature Value 64°
OFF 8 Enable for Negative Temperature Value
Temperature Upper Limit
‡
- - Z O N E 6 T E M P E R AT U R E S E N S O R - -
‡
This feature not evaluated by UL.