NAPCO Gemini GEM-P3200, Руководство по установке

Страница: 25 / 68

L
NAPCO Security Systems
X
GEM-P3200 Installation Instructions
WI817F 10/05 Page 25
3. Arm or disarm the selected area using your user code (the user code must be valid for that area).
4. To return the keypad to its "home" area, press the
G
button, then the
U
or
D
button.
Note: If the "home" keypad has been changed to one of the alternate areas and remains unused for more than 5 minutes,
it will revert back to the home area.
To arm all areas assigned to the user, press 9 G [User Code]
U
or
D
.
To disarm all areas assigned to the user, press 0 G [User Code]
U
or
D
.
Overview Mode
To enable or disable Overview, see ACTIVATE OVERVIEW function later in this section. The Overview Mode is a high
security mode of operation requiring a Level-3 User Code with Overview Option, wherein the status of both areas is displayed
at the keypad. When arming, the "home" area remains disarmed. To arm the alternate area, see Keypad Area Change, which
follows.
In the Overview Mode, "
OV(-)
" will be displayed, where each dash ("-") represents an area. In programmed areas, the dash
will be replaced by one of the following:
"A" = Area Armed
"B" = Burglary Zone in Alarm
"C" = Check Trouble; Area in Function-Display Mode
"F" = Fire Zone in Alarm
"R" = Area Ready (no faulted zones)
"T" = Fire Trouble
"Z" = Zone Fault
In the Overview Mode, the alternate ready area may be armed by pressing the
9 G
buttons. Note: The User Code
must be valid in that area. Similarly, the alternate armed area ("A") may be disarmed by pressing the
0 G
buttons. If
any zone is not secured, the system will not arm and the keypad will display "
CAN'T ARM SYSTEM / AREA # IN TROUBLE
", where "#"
represents the area number.
BYPASSING ZONES
Selective Bypass (Bypassing Specific Zones)
A Selective Bypass will bypass a specific zone that has Selective Bypass enabled, by pressing the
B
button followed
by the zone number. The zone will be unbypassed the next time the system is disarmed.
Security Bypass
Zones programmed for Selective Bypass may be removed from the system prior to arming as follows:
1. Enter a code valid for bypass (Authority Level 1 or higher and Bypass option enabled), then press the
B
button;
“
BYPASS ENABLED
” will display.
2. Press the
B
button, then the zone number (or vice versa) to deactivate that zone.
Note: When the panel is subsequently disarmed, all bypassed zones revert to unbypassed zones (unless Disable Auto-
Unbypass on Disarming is programmed or Interior Zones are programmed normally bypassed).
EZ Bypass (Do not enable in UL applications.)
Enable this feature by programming Disable Code Required for EZ Bypass. Then, zones programmed for Selective By-
pass may be bypassed quickly and easily as follows. Note: This is not a high-security feature.
1. At the “
SYSTEM READY
” or “
ZONE FAULT
” display, enter the zone number as a two-digit number (ex., “01”, “15”, etc.). Zones
cannot be bypassed while the panel is armed.
2. Press the
B
button. To unbypass the zone, press the
B
button again. Note: Steps 1 and 2 may be re-
versed and this feature will still function.)
Note: If Enable All-Zone-in-Trouble-Bypass is programmed, pressing the
G
and the
B
buttons simultaneously
will bypass all zones in trouble (except Fire and PIR Zones) that are also programmed for Selective Bypass.
Bypassing Interior Zones
Interior zones allow perimeter zones to be armed while part or all of the active interior remains disarmed. When the
P
button is pressed, the “
BYPASSED
” reminder will come on. Pressing the
U
button within 10 seconds will bypass the selected in-
terior group without arming, otherwise Interior Bypass will time out and the system will revert to the regular disarmed state. All
zones designated for the selected interior group(s) will be bypassed simultaneously when the system is armed. The alarm con-
ditions will then be stored in the Alarm History Log and the Total Event Log (see HISTORY LOG).
B
A
SIC OPER
A
T
IO
N