Nanni N4.40 Скачать руководство пользователя

Страница: 42 / 175

GENERAL

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

G-27

[12] CHECK POINTS FOR EVERY 1500 HOURS

CAUTION

• Examine the injection pressure and condition after you make sure that there is no one in the direction of

the fumes.

• If the fumes from the nozzle directly touches the human body, they can cause damage to the cells and

blood poisoning.

M00000003GEG0037US1

Nozzle Fume Condition
[D1503-M, D1703-M, D1803-M, V2003-M, V2203-M, V2403-M,
V2403-M-T, D1703-M-BG, V2003-M-BG, V2003-M-T-BG,
V2203-M-BG, V2403-M-BG]

1. Set the injection nozzle to a nozzle tester, and examine the

condition of the fumes from the nozzle.

2. If the fume condition is defective, replace the nozzle piece.

M00000003GEG0038US1

Nozzle Fume Condition
[D1803-M-DI, V2403-M-DI, V2403-M-DI-T]

1. Set the injection nozzle to a nozzle tester, and examine the

condition of the fumes from the nozzle.

2. If the fume condition is defective, replace the injection nozzle

assembly.

M00000003GEG0039US1

Fuel Injection Pressure
[D1503-M, D1703-M, D1803-M, V2003-M, V2203-M, V2403-M,
V2403-M-T, D1703-M-BG, V2003-M-BG, V2003-M-T-BG,
V2203-M-BG, V2403-M-BG]

1. Set the injection nozzle to a nozzle tester.
2. Slowly move the tester lever to measure the pressure at which

the fuel start to jet out from the nozzle.

3. If the measurement is out of the factory specifications, replace

the adjusting washer (1) in the nozzle holder.

(Reference)

• The pressure variation with 0.025 mm (0.00098 in.) difference

in washer thickness is approximately 590 kPa (6.0 kgf/cm

85 psi).

M00000003GEG0040US1

(A) Good

(B) Bad

(A) Good
(B) Bad

(a) 1.3 rad (72 °)

Fuel injection pressure

Factory spec.

13.73 to 14.70 MPa
140.0 to 150.0 kgf/cm

1992 to 2133 psi

(1) Adjusting Washer

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Результаты поиска

Содержание N4.40

Отзывы:

Похожие инструкции для N4.40

Бренды по названию

Популярные бренды

Nanni N4.40, Руководство по ремонту

Результаты поиска

Содержание N4.40

Отзывы:

Похожие инструкции для N4.40

Бренды по названию

Популярные бренды