Nanni N4.40 страница 158 Скачать руководство пользователя

Страница: 158 / 175

ENGINE

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

1-S88

(3) Piston and Connecting Rod

Piston Pin Bore I.D.

1. Measure the piston pin bore I.D. in the horizontal and vertical

directions with a cylinder gauge.

2. If the measurement is more than the allowable limit, replace the

piston.

M00000003ENS0130US1

Oil Clearance between Piston Pin and Small End Bushing

1. Measure the piston pin O.D. where it touches the bushing with

an external micrometer.

2. Measure the small end bushing I.D. with an internal micrometer.
3. Calculate the oil clearance.
4. If the oil clearance is more than the allowable limit, replace the

bushing.

5. If the oil clearance stays more than the allowable limit, replace

the piston pin also.

M00000003ENS0131US1

Replacement of Small End Bushing
(When removing)

1. Press out the used small end bushing with the replacing tool.

(See page

"SPECIAL TOOLS"

(When installing)

1. Clean a new small end bushing and bore, and apply engine oil

to them.

2. Make sure that the oil hole of the connecting rod aligns the

bushing hole. Then press fit the new bushing with the replacing
tool.

M00000003ENS0132US1

Piston pin bore I.D.

Factory spec.

25.000 to 25.013 mm
0.98426 to 0.98476 in.

Allowable limit

25.05 mm
0.9862 in.

Oil clearance between
piston pin and small end
bushing

Factory spec.

0.014 to 0.036 mm
0.00056 to 0.0014 in.

Allowable limit

0.15 mm
0.0059 in.

Piston pin O.D.

Factory spec.

25.004 to 25.011 mm
0.98441 to 0.98468 in.

Small end bushing I.D.

Factory spec.

25.025 to 25.040 mm
0.98524 to 0.98582 in.

(A) When Removing

(B) When Installing

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Результаты поиска

Содержание N4.40

Отзывы:

Похожие инструкции для N4.40

Бренды по названию

Популярные бренды

Nanni N4.40, Руководство по ремонту

Результаты поиска

Содержание N4.40

Отзывы:

Похожие инструкции для N4.40

Бренды по названию

Популярные бренды