Nanni N4.40 Скачать руководство пользователя страница 105

Страница: 105 / 175

ENGINE

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

1-S35

Fuel Injection Pressure
[D1803-M-DI, V2403-M-DI, V2403-M-DI-T]

1. Set the injection nozzle to a nozzle tester.
2. Slowly move the tester lever to measure the pressure at which

the fuel start to jet out from the nozzle.

3. If the measurement is out of the factory specifications, replace

the injection nozzle assembly.

M00000003GEG0041US1

Valve Seat Tightness
[D1503-M, D1703-M, D1803-M, V2003-M, V2203-M, V2403-M,
V2403-M-T, D1703-M-BG, V2003-M-BG, V2003-M-T-BG,
V2203-M-BG, V2403-M-BG]

1. Set the injection nozzle to a nozzle tester.
2. Increase the fuel pressure, and keep it at 12.75 MPa

(130.0 kgf/cm

, 1849 psi) for 10 seconds.

3. If you find a fuel leakage, replace the nozzle piece.

M00000003GEG0042US1

Valve Seat Tightness
[D1803-M-DI, V2403-M-DI, V2403-M-DI-T]

1. Set the injection nozzle to a nozzle tester.
2. Increase the fuel pressure, and keep it at 16.67 MPa

(170.0 kgf/cm

, 2418 psi) for 10 seconds.

3. If you find a fuel leakage, replace the injection nozzle assembly.

M00000003GEG0043US1

Fuel injection pressure
(1st stage)

Factory spec.

18.64 to 20.10 MPa
190.0 to 205.0 kgf/cm

2703 to 2915 psi

Valve seat tightness

Factory spec.

No fuel leak at
12.75 MPa
130.0 kgf/cm

1849 psi

Valve seat tightness

Factory spec.

No fuel leak at
16.67 MPa
170.0 kgf/cm

2418 psi

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Результаты поиска

Содержание N4.40

Отзывы:

Бренды по названию

Популярные бренды

Nanni N4.40, Руководство по ремонту

Результаты поиска

Содержание N4.40

Отзывы:

Бренды по названию

Популярные бренды