manualshive.com logo in svg

Nanni N4.40, Руководство по ремонту

Поделиться
Скачать
Nanni N4.40 Скачать руководство пользователя страница 40

GENERAL

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

G-25

Battery Specific Gravity

1. Measure the specific gravity of the electrolyte in each cell with a

hydrometer.

2. If the electrolyte temperature is different from the one that the

hydrometer calibrated, correct the specific gravity
measurement. Use the formula below in 

(Reference)

.

3. If the specific gravity is less than 1.215 (after it is corrected for

temperature), charge or replace the battery.

4. If the specific gravity is different between 2 cells by more than

0.05, replace the battery.

NOTE

• Hold the hydrometer tube vertically but do not remove it

from the electrolyte.

• Do not put too much electrolyte into the tube.
• Let the float move freely and hold the hydrometer at eye

level.

• You must read the hydrometer at the highest electrolyte

level.

(Reference)

• The specific gravity changes with temperature.

To be accurate, the specific gravity
decreases by 0.0007 when temperature increases by 1 °C
(decreases by 0.0004 when temperature increases by 1 °F),
increases by 0.0007 when temperature decreases by 1 °C
(increases by 0.0004 when temperature decreases by 1 °F).
Thus, if you refer to 20 °C (68 °F), correct the specific gravity
reading by the formula below :
–

Specific gravity at 20 °C = Measured value + 0.0007 ×
(electrolyte temperature 

−

20 °C)

–

Specific gravity at 68 °F = Measured value + 0.0004 ×
(electrolyte temperature 

−

68 °F)

At an electrolyte temperature of 20 °C (68 °F)

M00000003GEG0034US1

[10] CHECK POINTS FOR EVERY YEAR

Replacement of Air Cleaner Element

1. Remove used air cleaner element.
2. Replace it with a new one.

NOTE

• The air cleaner uses a dry element. Do not apply oil to it.
• Do not operate the engine without the filter element.

M00000003GEG0035US1

Specific Gravity

State of Charge

1.260 Sp. Gr.

100 % Charged

1.230 Sp. Gr.

75 % Charged

1.200 Sp. Gr.

50 % Charged

1.170 Sp. Gr.

25 % Charged

1.140 Sp. Gr.

Very Little Useful Capacity

1.110 Sp. Gr.

Discharged

(a) Good
(b) Bad

(c) Bad

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды