manualshive.com logo in svg

Nanni N4.40, Руководство по ремонту

Поделиться
Скачать
Nanni N4.40 Скачать руководство пользователя страница 113

ENGINE

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

1-S43

Solenoid

1. Disconnect the connector of the solenoid (1) (2P).
2. Examine the condition of the harness.
3. If the harness is defective, replace it with a new one.
4. Turn the key switch to the ACC position.
5. Measure the voltage between the terminals of the connector (2)

(harness side).

6. If the measurement is not in the factory specification, the ECU

is defective. Then replace the ECU with a new one.

7. If the measurement is in the factory specification, the ECU is

correct.
In this case, examine the solenoid in the procedure below.

(Reference)

1. Measure the resistance between the terminals of the connector

(solenoid side).

2. If the measurement is not in the factory specification, the

solenoid is defective. Then replace the solenoid with a new one.

3. If the measurement is in the factory specification, the solenoid

is correct electrically. Then examine the movement of the
solenoid.

4. Remove the solenoid (1) from the engine.
5. Apply the voltage of 12 V to the solenoid.
6. If the rod of the solenoid does not move smoothly, the solenoid

is defective. Then replace the solenoid with a new one.

7. If the rod of the solenoid moves smoothly, the solenoid is

correct.

M00000003ENS0056US1

Voltage

Factory 
spec.

Terminal 

1

 - 

Terminal 

2

12 V

Resistance

Factory 
spec.

Terminal 

1

 - 

Terminal 

2

2 to 4 

Ω

(1) Solenoid
(2) Connector (Harness Side)
(3) Terminal 

2

 (

−

)

(4) Terminal 

1

 (+)

(A) Key Switch OFF Position
(B) Key Switch ON Position

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды