manualshive.com logo in svg

Nanni N4.40, Руководство по ремонту

Поделиться
Скачать
Nanni N4.40 Скачать руководство пользователя страница 114

ENGINE

03-M-E3B, 03-M-DI-E3B, 03-M-E3BG, WSM

1-S44

Glow Plug Harness

1. Disconnect the wiring (1) of the glow plug.
2. Examine the condition of the wiring.
3. If the wiring is defective, replace it with a new one.
4. Turn the key switch to the ACC position.
5. Measure the voltage between the wiring (1) and chassis.
6. If the measurement is not in the factory specification, the ECU

is defective. Then replace the ECU with a new one.

7. If the measurement is in the factory specification, the ECU is

correct.
In this case, the glow plugs are defective.
Examine each glow plug, and replace the defective glow plug
with a new one.

M00000003ENS0057US1

Alternator

1. Disconnect the terminal 

L

 (2) of the alternator (2P).

2. Examine the condition of the harness.
3. If the harness is defective, replace it with a new one.
4. Measure the resistance between the terminal 

L

 (2) of the

connector (harness side) and chassis.

5. If the measurement is not in the factory specification, the ECU

is defective. Then replace the ECU with a new one.

6. If the measurement is in the factory specification, the ECU is

correct.
In this case, the alternator is defective. Then replace it with a
new one.

M00000003ENS0058US1

Speed Switch

1. Disconnect the connector of the speed switch.
2. Examine the condition of the harness.
3. If the harness is defective, replace it with a new one.
4. Measure the resistance between the terminals of the speed

switch when the speed switch turn on or off.

5. If the measurements are in the factory specifications, the ECU

is defective. Then replace the ECU with a new one.

6. If the measurements are not in the factory specifications, the

speed switch is defective. Then replace the speed switch with a
new one.

M00000003ENS0059US1

Voltage

Factory 
spec.

Terminal - 
Chassis

12 V

(1) Wiring of Glow Plug

Resistance

Factory 
spec.

Terminal 

L 

- 

Chassis

Infinity

(1) Alternator

(2) Terminal 

L

 (Harness Side)

Resistance

Factory 
spec.

ON

0 

Ω

OFF

Infinity

(1) Speed Switch (Switch Side)

(A) Single Pole, Single Throw
(B) Single Pole, Double Throw

KiSC issued 06, 2009 A

Содержание N4.40
















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды