background image

NAL Research Corporation (TN2012-02-V1.0) 

84 

 

S121 

 31 

Bitmap register: 

bit 0: +SBDMTA setting (SBD ring indication) 

bits 1-2: +SBDAREG setting (SBD automatic 
registration) 

bit 3: +CCWA<n> setting 

bit 4: +GPSSTA<n> setting 

Yes 

S122 

 31 

Bitmap register: 

bit 0: unused: 

bits 1-3: +CIER setting (indicator event 
reporting) 

Yes 

S123 

 255 

Bitmap register: 

bit 0: unused 

bit 1 = +WTM 

bit 2 = +WDLDM<dldm> 

bit 3 = +WIRLP<mode> 

bits 4-5 = +WFRNG 

Yes 

S124 

 255 

15 

Dynamic link measurement interval (+WDLM 
<mi> setting). Value in 1000 ms unit. 

 

S125 

 100 

10 

Dynamic link delay measurement delay 
tolerance (+WDLM<dtl> setting). Value in % 
unit. 

 

S126 

 255 

Bitmap register: 

0 = Ignore &Dn command specified reaction to 
DTR ON to OFF transitions. Disconnect as 
reaction to Hn command. OK response given. 

1 = Ignore &Dn command specified reaction to 
DTR ON to OFF transitions. Ignore Hn command. 
OK response given 

2 = Comply with &Dn command specified 
reaction to DTR ON to OFF transitions. 
Disconnect as reaction to Hn command. 

Yes 

S127 

 255 

Bitmap Register containing copies of 
MSVTR/MSVLS parameters: 

Bit 0 = –MSVTR: 0 = Disabled (default) 1 = 
Enabled 

Bit 1 = –MSVLS: 0 = No Mute (default) 1 = 
Mute Enabled 

Bits 2-5 = Reserved (see IID#2600) 

Yes 

Содержание A3LA-RS






































































































Отзывы: